Cleaning The Coffee-Making Unit - AEG Electrolux CP 2 Série Mode D'emploi

822_949_318 CP2..._defnep.book Seite 41 Freitag, 2. November 2007 6:30 18
0 To do this, proceed as follows (Fig. 24):
1. Push the Release catch for removing
grinding ring (Fig. 2, T) forward toward
the centre of the grinder.
2. Keep it in this position and turn the
Lever for setting grinding texture (Fig.
2, U) approximately one full turn
clockwise until it comes up against the
stop.
You can continue to turn the Lever for
3
setting grinding texture (Fig. 2, U) only
if the Release catch for removing
grinding ring (Fig. 2, T) is pressed.
0 Now release the grinding ring (Fig. 25)
and remove the foreign body or bodies.
1 Caution! Risk of injury from the spin-
ning grinder. Never switch the coffee
machine on, when you are working on
the grinder. This can lead to severe
injuries. Before starting work, ensure
that the machine is unplugged from
the mains socket.
3 When refitting the grinding ring,
ensure that both catches on the grind-
ing ring holder engage in the corre-
sponding slots (Fig. 25).
Failure to do this can lead to damage
to the grinder.
0 Turn the Lever for setting grinding tex-
ture (Fig. 2, U) approximately one full
turn anticlockwise until it comes up
against the stop.
0 Set the bean container in place at the
"UnlockContainer" position
turn it back to the "Coffee Beans" posi-
tion .
0 Add a small quantity of coffee beans,
and test the proper operation of the
grinder by making a cup of coffee. The
first time the grinder is used, or after
cleaning, less ground coffee will enter
the coffee-making unit, because the
channel first has to be filled. This can
influence the first cup of coffee.

15.5 Cleaning the Coffee-making Unit

We advise you to clean the coffee-
making unit regularly (depending on
how frequently it is used). It should be
cleaned before you start the cleaning
program. If your coffee machine is to
be left unused for some time (e.g. holi-
days), empty the coffee grounds con-
tainer and the water tank, and
thoroughly clean the coffee machine,
including the coffee-making unit.
Removing the coffee-making unit
0 Switch the coffee machine off with the
"On/Off" key (Fig. 3, h)
the coffee machine has reverted to the
standby position and the automatic
rinsing has ended. Then unplug from
the mains socket.
0 Pull the coffee grounds container com-
pletely out of the coffee machine
(Fig. 26).
0 Press the Service cover release button
(Fig. 2, S) (Fig. 27).
The service cover opens at the front
(Fig. 28).
0 Remove the service cover.
The coffee-making unit is located
behind the service cover (Fig. 29). The
three red elements are used for latch-
ing and unlatching.
0 To remove the coffee-making unit,
operate the latches in the following
order (Fig. 30):
1. Push the latching lever up.
2. Press and hold the lock button.
3. Press and hold the latching button
down and pull out the coffee-making
unit (Fig. 31).
Cleaning the coffee-making unit
, and
0 To clear coarse particles (contamina-
tion) from the coffee-making unit, pull
the red service lever down to the stop
and open the coffee-making unit
(Fig. 32).
The two strainers and now readily
accessible, and the ejector lever drops
down.
0 Rinse the coffee-making unit under
warm, running water. It is essential to
thoroughly flush the stainless steel
strainers to remove all coffee residues
(Fig. 33 and 34).
0 Dry the coffee-making unit off and
push the service lever back up to the
stop (Fig. 35).
g
. Wait until
41