Guarantee / Liability Exclusion; Ce Conformity Declaration; Configuration - Multiplex G-Sensor Mode D'emploi

3. Connection / Installation / Setup
The G Sensor is connected as follows:
· Insert the sensor cable (a)
into the socket labeled "MSB" or "Sensor" at the receiver.
The three-pin cable connector labeled "S" is used for
connecting additional sensors.
· Affix the sensor
to the fuselage base. Position the sensor as close as
possible to the model's center of gravity. The X-axis should
 run parallel and the Z-axis at right angles to the fuselage.
(Figures 1+2)
If required due to a lack of space, the sensor can also
be placed on the longitudinal side running parallel to the
X-axis. To do this, the sensor must be reconfigured using
the MULTIPLEX launcher.
After the G Sensor has been successfully installed and
the required connection established, it can be used
straight away.
· Launch your model.
· The current g-force is always displayed at address 5.
· The minimum and maximum g-forces occurring during
flight are displayed alternately at address 6.

4. Configuration

The easiest and most convenient way to configure the
G Sensor is by using the MULTIPLEX launcher.
You can find the MULTIPLEX launcher at
www.multiplex-rc.de in the download
section; the MULTIPLEX USB cable
(art. no.: 85149) is also required.
Configuration procedure:
· Pull the sensor cable (a) out of the socket on the receiver
and connect it to the USB-PC cable. To do this, you can use
the V-cable, which is enclosed along with the USB cable.
6
Z
a)
X
· Now start the MULTIPLEX launcher.
· Connect a 4-digit NiMH receiver battery to the free V-cable
connection. If the automatic identification does not work,
it may be necessary to select a COM port manually in the
"Connection" field.
· If the sensor has been identified correctly, the MULTIPLEX
sensor manager opens. Here, you can make the desired
settings.
· After clicking "send" and "finish", the sensor is ready to use
with the desired settings.

5 Guarantee / liability exclusion

The company of MULTIPLEX Modellsport GmbH & Co. KG accepts
no liability of any kind for loss, damage or costs which are in-
curred due to the incorrect use and operation of the product, or
are connected in any way with such use and operation. Unless
otherwise prescribed by binding law, the liability of MULTIPLEX
Modellsport GmbH & Co. KG to pay compensation, regardless of
the legal argument employed, is limited to the invoice value of
that quantity of goods made by MULTIPLEX Modellsport GmbH
& Co. KG which was immediately involved in the event in which
the damage occurred. This does not apply if MULTIPLEX Modell-
sport GmbH & Co. KG is deemed to have unlimited liability in ac-
cordance with binding law due to deliberate or gross negligence.
We guarantee our products in accordance with currently valid
legal regulations. If you wish to make a claim under guarantee
please contact the dealer from whom you purchased the product.

5.1 CE conformity declaration

This device has been assessed in accordance with the appropriate European harmonised directives. This means that you are the
owner of a product which, in terms of design and construction, satisfies the protective aims of the European Community for the
safe operation of equipment. A copy of the conformity declaration for the device can be requested from MULTIPLEX Modellsport
GmbH & Co. KG.
5.2 Disposal
Electrical apparatus which bears the cancelled refuse bin sym-
bol must not be placed in the domestic refuse, but taken to a
dedicated disposal system. In EU countries (European Union)
it is prohibited to dispose of electrical apparatus as domestic
waste (WEEE - Waste of Electrical and Electronic Equipment,
Directive 2002/96/EG).
The guarantee does not cover malfunctions which are caused by
the following:
· Improper use
· Incorrect or delayed maintenance, or maintenance carried
out by any party other than an authorised service centre
· Incorrect connections
· Use of accessories other than genuine MULTIPLEX / HiTEC
items
· Modifications or repairs not carried out by MULTIPLEX or a
MULTIPLEX Service Centre
· Accidental or deliberate damage
· Defects arising from normal wear and tear
· Operation outside the specified limits, or in conjunction with
components made by other manufacturers.
MULTIPLEX Modellsport GmbH & Co.KG
Westliche Gewerbestraße 1
D-75015 Bretten-Gölshausen - Germany
MULTIPLEX/HiTEC Service: +49 (0) 7252 - 5 80 93 33
You can take your old equipment to your local collection point
(e.g. recycling centre), where it will be recycled in the correct
manner at no cost to you. By recycling your old apparatus you
can make an important contribution to protection of the en-
vironment.

7