schmalz SCTSi IOL Notice D'utilisation page 68

IO-Link Data Dictionary
21.10.01.00077/05
146 0x0092 10 Condition Monitoring ejector #10
146 0x0092 11 Condition Monitoring ejector #11
146 0x0092 12 Condition Monitoring ejector #12
146 0x0092 13 Condition Monitoring ejector #13
146 0x0092 14 Condition Monitoring ejector #14
146 0x0092 15 Condition Monitoring ejector #15
146 0x0092 16 Condition Monitoring ejector #16
146 0x0092 17 Condition Monitoring of Control-Unit
Event Codes of IO-Link Events and ISDU 138 (Extended Device Status)
Event code Event name
Control-Unit
0x5100 General power supply fault
0x5110 Primary supply voltage over-run
0x5112 Secondary supply voltage fault
0x1812 Secondary supply voltage over-run
Supply pressure fault
0x1802
0x1811 Data Corruption
0x1000 General malfunction
Vacuum calibration OK
0x1800
0x1801 Vacuum calibration failed
0x8C01 Simulation active
0x180C Primary supply voltage out of optimal range
0x180D Secondary supply voltage out of optimal range
0x180E Supply pressure out of optimal range
Ejectors
0x8D00 Measurement range overrun, Ejector #1
...
0x8D0F Measurement range overrun, Ejector #16
0x8D10 Valve protection active, Ejector #1
...
0x8D1F Valve protection active, Ejector #16
0x8D20 Evacuation time t1 is greater than limit, Ejector #1
...
0x8D2F Evacuation time t1 is greater than limit, Ejector #16
0x8D30 Leakage rate is greater than limit, Ejector #1
...
0x8D3F Leakage rate is greater than limit, Ejector #16
0x8D40 H1 was not reached, Ejector #1
...
0x8D4F H1 was not reached, Ejector #16
0x8D50 Free-flow vacuum level too high, Ejector #1
...
0x8D5F Free-flow vacuum level too high, Ejector #16
J. Schmalz GmbH
1byte 0-99 ro
1byte 0-99 ro
1byte 0-99 ro
1byte 0-99 ro
1byte 0-99 ro
1byte 0-99 ro
1byte 0-99 ro
1byte 0-99 ro
IO-Link Event Type Extended Device Status Category
Error Critical condiction, high
Warning Critical condiction, high
Warning Critical condiction, high
Warning Critical condiction, high
Critical condiction, high
Warning
Error Defect/fault, high
Error Defect/fault, high
-
Notification
Notification -
Warning Warning, low
Warning Warning, high
Warning Warning, high
Warning Warning, high
Error Defect/fault, low
Error Defect/fault, low
Warning Warning, high
Warning Warning, high
Warning Warning, low
Warning Warning, low
Warning Warning, low
Warning Warning, low
Warning Warning, high
Warning Warning, high
Warning Warning, low
Warning Warning, low
J. Schmalz GmbH
Johannes-Schmalz-Str.1
D 72293 Glatten
Tel.: +49(0)7443/2403-0
Fax: +49(0)7443/2403-259
schmalz@schmalz.de
Bit 4 = Free flow vacuum too high
Bit 5 = Manual Mode Active
0
0
0
0
0
0
0
Bit 0 = Primary Voltage limit
0 Bit 1 = Secondary voltage limit
Bit 2 = Input pressure limit (3,5 ... 5bar)
Remark
Primary supply voltage (US) too low
Primary supply voltage (US) too high
Secondary supply voltage (UA) too low
Secondary supply voltage (UA) too high
Input pressure too high or too low
Internal error, user data corrupted
Internal error, Bus fault
Calibration offset 0 set successfully
Sensor value too high or too low, offset not changed
Manual mode is active in at least one ejector
Condition Monitoring: primary supply voltage US outside of operating range
Condition Monitoring: secondary supply voltage outside of operating range
Condition Monitoring: supply pressure outside of operating range
Vacuum value > 999 mbar in Ejector #1
Vacuum value > 999 mbar in Ejector #16
SCTSi series
26.09.2020
SCTSi Data Dictionary