Installing The Battery - Horizon Hobby Losi TENACITY-DB PRO RTR AVC 1:10 4WD DESERT BUGGY Manuel D'utilisation

EN

INSTALLING THE BATTERY

1. Ensure the ESC is powered OFF.
2. Remove the body clips and rotate the body up.
3. Remove the body clip from the battery hold down and open the battery tray.
4. Insert the battery into the battery tray.
The vehicle is setup at the factory for use with
a 2S LiPo battery. To install an optional 3S LiPo
battery, the included spacers must be added to
the battery tray as shown.
NOTICE: If you are using a 2S Li-Po battery,
use the included 17T Pinion gear. If you are
using a 3S Li-Po battery, use the optional 15T
pinion gear (included). Using a 17T pinion gear
with a 3S Li-Po battery will result in damage to
the ESC and motor.
SPEKTRUM™ DX3 RADIO SYSTEM
I
J
K
L
M
N
A/B
C
Battery/Programming Port
Steering Port
Throttle Port
AUX 1 Port
AUX 2 Port
AUX 3 Port
AUX 4 Port
4
5. Rotate the battery strap down, and insert the body clip to secure the battery.
6. Connect the battery power lead to the ESC, noting proper polarity.
7. Power ON the transmitter, then the vehicle.
8. Rotate the body into place, and insert the body clips.
IMPORTANT: Secure the ESC wires so they do not interfere with the gearing.
3S battery spacers
H
G
F
E
D
Bind Button
TENACITY-DB PRO RTR, AVC: 1:10 4WD DESERT BUGGY • INSTRUCTION MANUAL
A/B. Channel 3 Button
C. Throttle/Brake
D.
Steering Wheel
E.
Steering Rate - Adjusts the end point of the steering
F. Brake Rate - Adjusts the braking end point.
G. Steering Trim - Adjusts the steering center point. Normally, the steering trim is
adjusted until the vehicle tracks straight.
H. Throttle Trim - Adjusts the throttle neutral point
I. SMART Battery Level Indicator
J.
Servo Reversing - To reverse the Throttle (TH) or Steering (ST) channel, switch the
position of the correlating switch— "N" is for normal, "R" is for reverse.
K.
Throttle Limit - Limits throttle output to 50/75/100% Select 50% or 75% for less
experienced drivers or when you are driving the vehicle in a small area.
L. Power LED
• Solid red lights: Indicates radio connectivity and adequate battery power
• Flashing red lights: Indicates the battery voltage is critically low. Replace
batteries
M.
Power Button
N.
Bind Button
INSTALLING THE TRANSMITTER BATTERIES
1. Push in the battery cover a small amount to release the retaining tab, then remove the cover.
2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in the
transmitter's battery case.
3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.
For more information on the transmitter, go to www.horizonhobby.com and click
on the support tab for the Spektrum DX3 to download the instruction manual.
CAUTION: Never remove the transmitter batteries while the model is powered ON.
Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
Charging non-rechargeable batteries may cause the batteries to burst, resulting in
injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to national regulations.
SRS6200A AVC TECHNOLOGY RECEIVER
AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power supply for a
personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational.
The remaining Aux channels can be used to power a personal transponder or lights.
If AVC is disabled (see DISABLING THE STABILITY ASSIST FUNCTION), all 6 channels
including the Aux channels can operate as servo channels.