Control; Brightness Of The Temperature Display; Child Proofing; Door Alarm - Atag KD8122AF Mode D'emploi

5 Control

5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
The brightness can be adjusted between h1 (minimum lumi-
nance) and h5 (maximum luminance).
u To activate the setting mode: Press the Fast Cool button
Fig. 2 (5) for about 5 seconds.
w The Fast Cool button flashes. The display indicates c.
u Using the "+" setting button
select Fig. 2 (2) h.
u To confirm: Briefly press the Fast Cool button
u To make the display brighter: Press "+" button
Fig. 2 (3) .
u To make the display darker: Press "-" button
Fig. 2 (2) .
u To confirm: Press Fast Cool button
w The brightness is adjusted to the new value.
u To deactivate the setting mode: Press the On/Off button
Fig. 2 (4) .
-or-
u Wait for 5 minutes.
w The temperature is indicated again in the temperature
display.

5.2 Child proofing

The child-proofing function enables you to make sure that the
appliance is not inadvertently switched off by playing children.
5.2.1 Setting the child lock
u To activate the setting mode: Press the Fast Cool button
Fig. 2 (5) for about 5 seconds.
w The Fast Cool button flashes. The display indicates c.
u Briefly press the Fast Cool button
u Switch ON: Using the "+" setting button
Fig. 2 (2) c1.
or "-" setting button, select
u Switch OFF: Using the "+" setting button
Fig. 2 (2) c0.
or "-" setting button, select
u To confirm: Press the Fast Cool button
w The child lock is switched on when the child lock symbol
Fig. 2 (7) shines.
u To deactivate the setting mode: Press the On/Off button
Fig. 2 (4) .
-or-
u Wait for 5 minutes.
w The temperature is indicated again in the temperature
display.

5.3 Door alarm

If the door is open longer then 60 s, the audible alarm sounds.
The audible alarm is automatically silenced when the door is
closed.
5.3.1 Muting the door alarm
The audible alarm can be muted when the door is open. The
sound switch-off function is active as long as the door is left
open.
Fig. 2 (6) .
u Press alarm button
w The door alarm is silenced.
Fig. 2 (3) and "-" setting button,
Fig. 2 (5) .
Fig. 2 (5) .
Fig. 2 (5) for confirmation.
Fig. 2 (3)
Fig. 2 (3)
Fig. 2 (5) .

5.4 Refrigerator compartment

The natural circulation of air in the refrigerator compartment
results in zones differing in temperature. It is coldest directly
above the plate separating off the ClimatFreshbox zone and at
the rear wall. It is warmest at the top front of the compartment
and in the door.
5.4.1 Food refrigeration
Note
The energy consumption increases and the cooling perform-
ance decreases if the ventilation is inadequate.
u Always keep the air slits of the fan free.
u Store perishable food such as ready-to-serve dishes, meat
products and sausages in the coldest zone. Place butter
and preserves in the upper area and in the door (see Appli-
ance at a glance).*
u Place butter and preserves in the upper area and in the door
(see Appliance at a glance).
u Use recyclable plastic, metal, aluminium and glass
containers and cling film for wrapping.
u Use the front area of the refrigerator compartment floor only
for briefly putting down cooled products, e.g. when rear-
ranging and sorting. However do not leave cooled products
there otherwise they may be pushed back or tipped over
when the door is closed.
u Do not store food too close together to enable good air
circulation.
u To safeguard bottles from tipping over: move the bottle
holder.
5.4.2 Setting the temperature
The temperature can be set from 9 °C to 4 °C , the recom-
mended temperature is 5 °C.
An average temperature of about –18 °C is reached in the
freezer compartment.*
Note
If the temperature is to be colder than 4 °C:
u set the cooling temperature to 4 °C.
u Set the ClimatFreshbox temperature to a value between b4
(slightly colder) and b1 (coldest) .
u For a higher temperature setting: press "+" button
u For a lower temperature setting: press "-" button
w The first time the button is pressed, the value set so far is
indicated in the temperature display.
u To change the temperature in 1 °C steps: briefly press the
button.
u To change the temperature continuously: hold down the
button.
w The value is displayed flashing during the setting operation.
w The actual temperature is displayed about 5 s after the last
press of a button. The temperature slowly adjusts to the new
value.
5.4.3 Fast Cool
Use Fast Cool to activate the highest cooling performance to
reach lower cooling temperatures. Fast Cool is used for rapidly
cooling large amounts of food.
Fast Cool has a slightly higher energy consumption
To cool using Fast Cool
u Briefly press the Fast Cool button
Fig. 2 (5) shines.
w The Fast Cool button
w The cooling temperature drops to the coldest value. Fast
Cool is switched on.
w Fast Cool switches off automatically after approx. 6 hours.
The appliance continues to operate in the energy-saving,
normal mode.
Control
Fig. 2 (3) .
Fig. 2 (2) .
Fig. 2 (5) .
23