Fader Start Function - Pioneer DJM-400 Mode D'emploi

FADER START FUNCTION

By connecting the optional Pioneer DJ CD Player control cable, the
channel fader and cross fader can be used to start CD playback.
When the mixer's channel fader lever or cross fader lever are moved,
the CD player is released from the pause mode and automatically –
and instantly – begins playback of the selected track. Also, when the
fader lever is returned to its original position, the CD player returns to
its cue point (back cue), thus allowing "sampler" type play.
Cross fader start play and back cue play
When the CD player assigned to channel 1 is set to standby at a cue
point, moving the cross fader lever from the right (2) side toward the
left (1) side, automatically starts play on the channel 1 CD player.
When the cross fader lever reaches the left (1) side, the CD player
assigned to channel 2 goes to back cue (returns to cue point). Also,
when the CD player assigned to channel 2 is set to standby at a cue
point, moving the cross fader lever from the left (1) side to the right
(2) side, automatically starts playback on the channel 2 CD player.
When the cross fader lever reaches the right (2) side, the channel 1
CD player goes to back cue (returns to cue point).
* The back cue is performed even if the input selector switch is not
set to [CD].
[Using the Channel Fader to Start Playback]
MIC
2
FADER
START
HEADPHONES
(CH-2)
3 5
2
FADER
START
(CH-1)
1
THRU/
1. Set the cross fader selector switch to the left (THRU)
position.
2. Press the FADER START button for the channel (1 to 2)
connected to the CD player you wish to control.
¶ The button for the selected channel lights.
3. Set the channel fader lever to its lowest position.
4. Set the CD player to the desired cue point, and engage cue
point standby.
¶ If a cue point has already been set, it is not necessary to set the
CD player to standby at the cue point.
5. At the instant you wish to start playback, move the
channel fader lever.
¶ CD player begins playback.
¶ After playback has begun, if the channel fader lever is returned
to its minimum position, the CD player returns to the cue point
and reenters standby mode (back cue).
* If the cross fader selector switch is set to a position other than
[THRU], the cross fader control is enabled and channel fader
cannot be used for control.
MASTER
BEAT EFFECTS
/
MIXER OPERATIONS (FADER START FUNCTION)
[Using the Cross Fader to Start Playback]
MIC
2
FADER
HEADPHONES
START
(CH-2)
2
FADER
START
(CH-1)
1
THRU/ /
1. Set the cross fader selector switch to the middle (
right ( ) position.
2. Press the FADER START button for the channel (1 to 2)
connected to the CD player you wish to control.
¶ The button for the selected channel lights.
3. Set the cross fader lever fully to the opposite side from the
channel you wish to start.
4. Set the CD player to the desired cue point, and engage cue
point standby.
¶ If a cue point has already been set, it is not necessary to set the
CD player to standby at the cue point.
5. At the instant you wish to start playback, move the cross
fader lever.
¶ CD player begins playback.
¶ After playback has begun, if the cross fader lever is moved fully
to the side opposite from its start, the CD player assigned to the
opposite side channel will return to the cue point and enter
standby mode (back cue).
* If the cross fader selector switch is set to [THRU], channel fader
operation is enabled, and the cross fader cannot be used to
control playback.
MASTER
BEAT EFFECTS
3 5
) or the
<DRB1404>
9
En