Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
10. Commissioning
10.1 Commissioning of the outdoor station
After inserting the batteries the power LED [54] lights green for 5 seconds only.
Now the outdoor station is in standby operation. If the power LED lights red the
batteries are weak and should be replaced.
If the outdoor station is powered by the mains adapter the power LED [54]
lights green for 5 seconds and then flashes once per minute to indicate the
standby operation.
10.2 Commissioning of the indoor station
! Remove the protective foil from the monitor [33].
! Press the on/off button [35]. The Power-LED [54] lights blue to indicate
the standby operation.
! The Lithium battery starts charging automatically when the mains adapter
is connected. Let the battery charge for 8 hours before portable use of the
indoor station (without the mains adapter). Pay attention to the Battery-
charge LED [55]:
! Lights green:
battery charging, leave mains adapter connected
until LED goes off
! Lights red:
battery charge low, monitor will automatically
switch off within 3 minutes
! Not illuminated:
battery is charged
! To turn off the indoor station press the on/off button [35] for up to 3
seconds until the message "Power OFF" is displayed on the monitor.
11. Basic operation
!
! If the outdoor station is powered using the mains adapter and the indoor
station is in standby operation the camera picture can be viewed at any
time by pressing the direction button
automatically switch off after one minute. This function is not available if
the outdoor station is powered by batteries, in this case the message "no
signal" is displayed on the monitor.
! If the doorbell button [10] is pressed a chime is heard from the indoor
station, and also as confirmation from the outdoor station. The camera
image appears on the monitor [33]. If no further button is pressed the
camera image switches off after one minute.
! Whilst the camera image is displayed the sound at the microphone [6] of
the outdoor station can be heard through the speaker [56] of the indoor
station. Adjust the volume by pressing the direction button [53]
or
VOL+. The set volume (between 0 and 6) is displayed for a short
time on the monitor.
! To speak with the visitor press the button [52]
image is displayed. A
corner of the monitor.
! If a door release is fitted to the outdoor station this can be activated
through a 12 V DC impulse by pressing the button [50]
is not available if the outdoor station is powered by battery.
! In low ambient light levels the infrared LEDs [12] will be activated by the
daylight sensor [11]. The close range up to 0.8 m in front of the outdoor
station is illuminated. In order to obtain a better image in darkness
additional lighting must be installed.
[53]. The image will
whilst the camera
Symbol is displayed at the lower left hand
. This function
! If the indoor station does not react to the pressing of the doorbell button,
but the chime is confirmed at the outdoor station, first check that the indoor
station is in standby operation (power LED [54] lights blue). Then reduce
the distance between the indoor and outdoor station. If there is still no
reaction to the doorbell signal then the stations must be paired with each
other (see chapter 12.2). The strength of the received wireless signal is
indicated in the top left hand corner of the monitor. Up to 4 vertical bars
next to the antenna symbol indicate the reception strength: no bars = no
signal, 1 bar = poor reception, ....4 bars = optimal reception.
12. Advanced operation
12.1 On-Screen Menu
The settings in sections 12.2 to 12.5 can be made using the on-screen menu:
! Select the on-screen menu by pressing the Menu button [35].
! Press the buttons [53]
the menu points.
! Press the buttons [53]
the settings.
! Press the ESC-button [50] repeatedly to exit the on-screen menu.
! If no direction button is pressed with a period of approx. 20 seconds the on-
screen menu will be automatically exited.
12.2 Camera Setup
Camera brightness
If necessary, the picture can be adjusted to suit the ambient light level.
! Move the cursor to
select the setting by pressing the OK button
[52]. Set the required brightness using the
direction buttons [53]
brightness is displayed on a scale for a short
period.
Pairing of indoor and outdoor station
The stations in the set are already paired with each other in the factory. If there
is no connection they should be paired again:
! Move the cursor to
setting by pressing the OK button [52]. A
circular symbol rotates for up to 60 seconds.
Within this period depress the doorbell button
[10] and then the Pairing button [16] on the
VOL-
outdoor station. Upon successful connection the
camera image will be appear on the monitor.
12.3 Recorder Setup
Video and audio sequences can be recorded after inserting an SD card (max.
32 GB, not supplied) in the SD card slot [36]. Whilst a camera image is
displayed on the monitor recording can be started and stopped by repeated
pressing of the
the SD card can be set up in the on-screen menu.
! Move the cursor to
this function to "ON" or "OFF" using the
direction buttons [53]
function is enabled then a video and audio
and
to select
and
to change
camera brightness and
and
. The
Pairing and select this
button [51]. Automatic recording and the parameters for
Visiting Record. Set
and
.When this
GB - 31
Publicité
Table des Matières
