GRAUPNER SJ ULTRA DUO PLUS 80 Instructions D'utilisation page 42

Balancer view:
Only available for LiXX batteries if the battery is connected to the balancer.
Pressing the INC or DEC button calls up the voltage display for the individual
cells.
The two bars adjacent to the highest / lowest cell voltage show the difference
between the voltages in graphic form: the upper bar (highest cell voltage) is
always the maximum length, while the lower bar (lowest cell voltage) varies
to show the actual difference; the discrepancy is also displayed as a numeric
value.
System menu:
The System menu is accessed by pressing and holding the MODE button
while you connect the charger to the power supply. In this menu you can
set the contrast of the LCD screen (LCD CONTRAST: 1 - 30, default set-
ting: 12), and switch the screen backlight (LCD BACKLIT) on or off.
If you wish to enter a user name, move the Select arrow to the USER
NAME line using the INC or DEC button: the arrow is now below the letters
line. Use the INC or DEC button to select the appropriate letter, then press
ENTER to highlight it; you can now alter it using the INC or DEC button.
Press ENTER again to store the letter you just selected. Once you have
entered the complete name, press ESC to leave the System menu and return to the Start screen.
Resetting the ULTRA DUO PLUS 80 to the factory default settings:
To reset the charger, hold the ESC button pressed in while you connect the charger to the power supply.
PC interface (Mini-USB)
Via the rear PC interface firmware updates will be done with the included USB cable. For the firmware and USB drivers, see under www.graupner.de/en
in the download area of the charger. A detailed update guide is also available under this link.
We have been working closely with the manufacturer of the software 'LogView', in order to provide optimum facilities for evaluating the data generated
by the ULTRA DUO PLUS 80 battery charger. With the help of LogView, which we recommend and support, it is possible to visualise and analyse the
serial data delivered by these chargers, and if necessary to export the data in a wide variety of forms.
The software is Donationware, and can be downloaded from the following web addresses: www.graupner.de or www.logview.info. If you enjoy using the
software, there is a method of sending a monetary contribution to the developer, but otherwise the program can be used free of charge.
42
3S=11.845V
Highest and lowest
33.95V
3
13.94V
cell voltage 1
Total cell count and
0 ] NiMH
voltage

CYCLE
CHG.
DCHG.
3S=11.845V
Highest and lowest
33.95V
3
13.94V
cell voltage
1
0 ] NiMH

CYCLE
CHG.
DCHG.
Press and hold the MODE button
while you connecting the power
supply.
Mode
LCD CONTRAST:

LCD BACKLIT :
Power < USER NAME...
ABCDEFGHIJKLMNOPQ
On
Press and hold the MODE button
RSTUVWXYZ abcdefg
while you connecting the power
hijklmnopqrstuvwx
Connect supply.
yz 0123456789 -.'
Mode
power supply
LCD CONTRAST:

LCD BACKLIT :
< USER NAME...
Power
ABCDEFGHIJKLMNOPQ
On
RSTUVWXYZ abcdefg
hijklmnopqrstuvwx
Connect
yz 0123456789 -.'
power supply
Voltage difference
1S=3.944V 1
between the highest
and lowest cells
Press the 'Inc' or 'Dec'
8mV
button to display
6S 3300mAh
specific cells
: C-> D 1X 10m
: 3.3A 5mV/C
: 5.0A 0.8V/C
Voltage difference
1S=3.944V
1
between the highest
and lowest cells
8mV
6S 3300mAh
: C-> D 1X 10m
: 3.3A 5mV/C
: 5.0A 0.8V/C
10
ON
ULTRA DUO-----
>
ESC
------ PLUS 80
Version 1.00
< USER NAME...
10
ON
ULTRA DUO-----
>
ESC
------ PLUS 80
Version 1.00
< USER NAME...
Operating Manual ULTRA DUO PLUS 80
>
>