Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
you have any complaints please contact the
Assistance Service.
_ Booklet : basket; 2 back wheels with brake
lock, back wheel axis, 2 front wheels,
handlebar, hood.
INSTRUCTIONS
1 OPENING: Before opening the frame, remove
(without using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER
BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY
HANDLE OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES
TO THIS FEATURE.
Press down the side fastener, hold the upper
section of the handle and rotate it towards you
until the frame is fully opened (fig_a). Open
frame (fig_b).
The frame is properly opened when the
attachment on the base clicks into place, as
shown.
2 FITTING THE WHEELS: Slot the uprights into
the rear wheel crosspiece (fig_a), ensuring
that it is facing the right way, then push the
rear wheels on and make sure that they click
into place (fig_b). To mount the front wheels, fit
them into the uprights until they lock into place
(fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
the figure (Fig_b).
To complete the operation, press the two
side buttons on the handle (Fig_c) to ensure
the handle pushes in all the way, until it clicks
into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the basket
tube to the horizontal position. Press the silver
buttons under the metal basket tube located at
the back of the stroller (fig_a) and remove the
metal tube (fig_b). Thread the tube through the
fabric loop on the back of the basket, making
sure that the two silver buttons are facing
downward (fig_c). Re-attach the tube to the
housings (fig_d).
5 Secure the two upper basket vinyl eyelets to the
two grey buttons on either side of the metal tube
housing. Please note that the eyelets open (fig_e).
Remove the cardboard from the lower rear bar.
IMPORTANT! Secure the two lower basket vinyl
eyelets to the two grey buttons on the top of the
lower rear bar. Please note that the eyelets open
(fig_f).
WARNING! If this operation is not performed
correctly, the basket will not properly hold the
weight.
Attach the basket tabs to the grey buttons on the
front of the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS
VIDEO AT:
WWW.PEGPEREGO.COM
6 Attach the back of the hood with Velcro (fig_a),
slide the hood attachments into their slots
(fig_b), fasten the elastic straps to the buttons
placed inside the handle (fig_c), and button the
sides of the hood to the frame (fig_d).
7 FIXED OR SWIVELING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(fig_a) and lower them to allow the wheels to
swivel (fig_b). On uneven surfaces, the wheels
should be set to their fixed position.
8 BRAKE: Press the lever down to apply the brake
on the chassis and lift it to release the brake.
9 ADJUSTABLE HANDLEBAR: To adjust the
height of the handlebar, press both of the
side buttons at the same time (fig_a) and
swing it into the desired position (fig_b),
then release the buttons.
10 FOOTREST: before adjusting the foot rest,
ensure its cover is accurately fitted; if it isn't,
fit it accordingly. To lower the footrest push
the two levers downwards and then push
the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
11 HOOD: the hood has a sun canopy. Pull it out
from inside the hood (fig_a).
The hood has an eyelet from which to hang
the baby's favourite toy (fig_b) and a clear
window which allows you to see your child
(fig_c). To lift it, remove the elastic from
around the button. You can unfasten the
Velcro strap and roll up the back of the hood,
fixing it up with the elastic, for increased
ventilation when using the stroller with the
backrest lowered.
12 ADJUSTING THE BACKREST: to lower the
backrest, press the clip and the backrest will
move down to the desired position.
To raise the backrest, press the clip and lift
the backrest to the desired height.
13 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached – arrow_a) into
the leg divider until they click into place
(arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
14 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it, move it in the opposite direction.
15 Before adjusting the height of the safety
harness remove the shoulder pads (fig_a). To
adjust the height, slip the belts through the
eyelet in the fabric (fig_b) and position them
in the most suitable eyelet.
16 FOLDING UP: To fold the stroller, it is best to
set the front wheels to their fixed position
and close the hood (if fitted). Place the handle
as shown in the figure (fig_a).
- 13 -
Publicité
Table des Matières
