Playing A Preset Dab Station; Dab Settings Menu; Remote Unit Advanced Buttons; Troubleshooting - Rotel T14 Manuel De L'utilisateur

14

Playing a preset DAB station

When a DAB station is playing, you can switch to a preset station in one
of the following ways.
3 D
1. From the numeric keypad
station.
2. Press the PRESET +/- H buttons on the remote control to display preset
numbers. Press the up/down
buttons on the remote control or turn the knob
select the desired station, then press the PUSH SELECT knob
front panel or the ENT button on the remote control.

DAB Settings Menu

q M
Press DAB on the front panel or remote control, to toggle to the DAB
settings Menu. Turn the PUSH SELECT knob
up/down arrow buttons on the remote control to go through each sub-menu.
• <STATION LIST>: Shows stations list.
• <LOCAL SCAN>: Start a limited scan of available stations by pressing
the PUSH SELECT knob 8
remote control. (Not available in all markets.)
• <FULL SCAN>: Start a full range scan by pressing the PUSH SELECT
knob 8 on the front panel or the ENT button on the remote control.
• <MANUAL TUNE>: Press the PUSH SELECT knob
or the ENT button on the remote control and select stations manually by
turning PUSH SELECT knob
arrow buttons on the remote control.
• <DRC>: Dynamic Range Control, select between "off", "high" and
"low". Turn the PUSH SELECT knob
up/down arrow buttons on the remote control to change and press the
PUSH SELECT knob 8 on the front panel or the ENT button on the
remote control to save.
• <STATION ORDER>: Display station order as either "Alphanumeric",
"Ensemble" or "Valid".
• <PRUNE STATION>: Select between "Yes" or "No". The Prune setting
allows you to remove stations that are not active or can not be received.
NOTE: Prune will remove unavailable stations from both the Station
List and the DAB Preset List.
• <DAB PRESET>: Displays all 30 of the DAB/DAB+ preset stations and
allows tuning to the selected preset by pressing the PUSH SELECT knob
8
on the front panel or the ENT button on the remote control.
, press the preset number of the desired
B arrow buttons or the PRESET +/-
8
on the front panel to
8
on the front panel, or use the
on the front panel or the ENT button on the
8 on the front panel
8 on the front panel or using the up/down
8 on the front panel or use the

Remote Unit Advanced Buttons

MENU Setting J
To enter the setup menu, press the MENU
and you will see the following display to configure additional settings:
SETUP
> POWER OPTION
H DISPLAY DIMMER
8
on the • POWER OPTION: In Normal mode, the network connection is turned OFF
when the unit is in standby mode. Setting this to Quick leaves the network
connection active during standby mode. Use Quick mode to reduce the
power on time allowing the network to stay connected. "Normal" is the
factory default.
Valid settings include: Quick, Normal.
NOTE: When the POWER OPTION is configured to Quick, the T14
will consume additional power in standby mode.
• DISPLAY DIMMER: Changes the display brightness.
• POWER LED DIMMER: Changes the Power LED brightness.
NOTE: These settings are stored permanently even after the T14 is
powered off.
• VERSION: Shows the current software version.
• EXIT: Exits this setting menu.
DIM Button C
Remote Only
Press the DIM button repeatedly to change the DISPLAY brightness.
NOTE: Adjustment made using the DIM
and not saved after powering off the T14.

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the area of the
difficulty, check the control settings, determine the cause of the fault and
make the necessary changes. If you are unable to get sound, refer to the
suggestions for the following conditions:
Power Indicator Is Not Illuminated
The power Indicator should be illuminated, either Blue (on) or Red (standby),
whenever the unit is plugged into the wall power outlet and the power button
is depressed. If it does not illuminate, test the power outlet with another
electrical device, such as a lamp. Be sure the power outlet being used is
not controlled by a switch that has been turned off.
T14 Network/FM/DAB+ Tuner
J button on the remote control
C button is temporary only