Important Charging Notes; Installing And Removing The Battery Pack - Black & Decker BHFEA18 Mode D'emploi
Masquer les pouces
Voir aussi pour BHFEA18:
Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the red light
continuously flashing a short ON followed by a longer ON
(see charger for blink pattern). Once the battery pack has
reached an appropriate temperature, the charger will resume
the charging procedure.
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and remove
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Assembly (Fig. C)
1. Align the top of the extension tube
inlet
15
as shown in Fig. C.
2. Push the extension tube
it locks into position.
8
Shock hazard. Disconnect the
To reduce the risk of
8
with the vacuum
8
onto the vacuum inlet
3. To remove an accessory, press the extension pole release
button
7
of the extension tube and gently pull the connected
accessory off.
WARNING:
unit with the rear of the vacuum facing a wall so that
any inadvertent fall of the unit would contact a wall
and not people or pets.
OPERATION
WARNING:
serious personal injury, turn unit off and remove
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. F)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
13
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Use (Fig. A, G)
This vacuum cleaner can be used in one of two ways.
•
With the extension tube
•
With the crevice tool
Switching ON and OFF (Fig. H)
•
To switch ON, push the ON/OFF button
•
For increased power, push the ON/OFF button
nOTE: The state of charge indicator LEDs will illuminate
while the vacuum is ON.
•
To switch OFF, press the ON/OFF button
Floor Sense
Floor Sense is active in the low speed. When a carpet is
detected, the performance of the unit is automatically
increased to high speed. When a hard floor is detected, the
performance of the unit reduces to low speed.
Using an Accessory Tool (Fig. G)
The crevice tool
hard to‑reach places.
•
To attach the crevice tool
so it locks into position as shown in Fig. G.
•
To release the crevice tool
15
so
release button
located on the vacuum inlet or the bottom
When not in use position the
To reduce the risk of
12
into the tool handle, align the
8
and the floor head
11
.
11
allows for vacuuming in narrow and
11
press into vacuum inlet
11
press the crevice tool
16
and gently pull the extension tube off.
9
.
1
.
1
again.
1
a third time.
15
Publicité
Table des Matières
