Safety Information - Burda PERFECTCLIME PCE05 Montage Et Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

A
SSEMBLY AND OPERATING INSTRUCTIONS
Dear Customer,
please read the following information carefully before using
the appliance for the first time for your own safety and to
ensure correct use.
D
:
ESIGNATED USE
Outdoor areas.
S
I
:
AFETY
NFORMATION
• The electrical system connected to the device must
comply with the laws of the country of installation.
• Do not use the device if it is damaged or impaired, unplug
the power cord and contact the service center.
• Observe the regulations of the fire brigade or the local
authority.
• Do not touch the plugs with wet hands or feet!
• Avoid accidental starting, set the switch to OFF before
inserting or removing the power plug.
• Do not pull on the power cord to pull the plug. Chemicals
should be used with care to avoid damaging the
components of the machine and the environment.
• Do not install the machine near flammable products
(focus on environments with suspended particles: plastics,
resins, acids, paints, etc.).
• Always check the biodegradability and aggressiveness of
the products used.
• Do not use paints, acids, solvents, oily or very dense
liquids.
• The device should be connected by trained personnel.
• Do not leave the machine unattended, especially when
children are present.
• The operational device is to be monitored by the
operator.
• Suitable external precautions (canopies, covers) against
weather conditions which could impair functionality (rain,
snow, hail, etc.) are precautions which are the responsibility
of the purchaser.
D
:
ISCLAIMER
The manufacturer is released from any liability in the
following cases:
• Misuse or unauthorized use of the machine by untrained
personnel.
• Use not in accordance with the applicable laws
• Deficiency in the maintenance included.
• Changes which do not comply with the applicable laws.
• Failure to comply with all or part of the instructions.
P
:
OWER CORD
• The power cord must not come into contact with hot
appliance parts!
• Never pull the plug out of the socket at the cord! Never
move the appliance by pulling at the cord or use the cord
for carrying purposes!
• Do not coil the cord around the appliance! Do not use the
appliance with the cord coiled!
• Do not crush the cord or drag it over sharp edges or place
it over heated hotplates or naked flames!
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard
P
& I
REPARATION
NSTALLATION OF THE PUMP
• Please make sure the inlet hose is tightly fastened to the
misting system and to the faucet. ONLY CLEAN WATER
SHOULD BE USED.
• Install discharge hose by placing the open end of the
clear hose in a drain or another location where water can
be safely discharged.
• Assemble the mist line, nozzles and the connector
assemblies according to the instructions that match the
type of mist line purchased.
• After the mist line is installed, connect the mist line to the
system outlet using high-pressure supply hose.
• Plug in the power cable after confirming the power supply
matches the system requirements.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
Do not put the unit into operation until it has
been completely installed.
A
: Please check whether the inlet pressure
TTENTION
from the faucet is between 4 psi and 56 psi
(0.3kgf/cm2~4kgf/cm2). If the inlet pressure is lower than 4
psi, the misting system will not start. If the inlet pressure is
over 56 psi, the misting system may be damaged.
M
I
:
IST LINE
NSTALLATION
• Please make sure flexible mist hoses are connected to the
misting system via the connectors.
• Please assemble the line at ground level before installing
at the desired height.
• Please use fasteners or fittings to secure the stainless steel
pipes or flexible mist hoses tightly at the installation site.
• If necessary, use a pipe-bending tool to alter the shape of
stainless steel pipes.
A
: When flushing out the mist line, be certain
TTENTION
to direct the path of the spray away from people, animals
and electrical goods. Water will be traveling at high velocity
and may cause personal injury and/or property damage.
GB

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Perfectclime pce1

Table des Matières