Burda PERFECTCLIME PCE05 Montage Et Mode D'emploi page 11

S T S A S
ETTING HE PRAY ND TOP INTERVAL
[Example] How to make the "Spray 3 minutes and stop 50 How to make the "Spray 3 minutes and stop 50
seconds" setting:
Setting the spraying time:
• Use the "Spray Time Setting Dial" and turn it to 3 • Use the "Spray Time Setting Dial" and turn it to 3
• Set the switch to "M" which is left of "Spray Time Setting • Set the switch to "M" which is left of "Spray Time Setting
Dial"
• Set the switch to "1" to get one time setting witch to "1" to get one time setting
The system will spray for 3 minutes.
• Possible time setting min. 15 sec. max. 60 m in. 15 sec. max. 60 min.
Setting the stop spraying time:
• Use the "Stop Spraying Setting Dial" and turn it to 5. • Use the "Stop Spraying Setting Dial" and turn it to 5.
• Set the switch to "S" which is left of "Stop Spraying
Setting Dial".
• Set the switch to "10" to get ten times setting. • Set the switch to "10" to get ten times setting.
The system will remain stopped for 50 seconds The system will remain stopped for 50 seconds.
• Possible time setting min. 15 sec. max. 60 m in. 15 sec. max. 60 min.
Setting the Pressure Release Time:
• The maximum pressure release time is 15 seconds. release time is 15 seconds.
• The stop spraying time must be longer than pressure The stop spraying time must be longer than pressure
release time in order to make sure the two actions do not release time in order to make sure the two actions do not
overlap.
• The longer misting line, the more pressure release time is • The longer misting line, the more pressure release time is
needed.
• Every time the pump stops a signal from the timer will Every time the pump stops a signal from the timer will
cause the pressure release solenoid valve to open, cause the pressure release solenoid valve to open,
depressurizing the mist line.
• The benefit of this is reducing the water dripping from the The benefit of this is reducing the water dripping from the
nozzles. The setting of this knob determines the duration of nozzles. The setting of this knob determines the duration
that signal and how long the valve stays open. that signal and how long the valve stays open.
• There are several factors which affect the residual There are several factors which affect the residual
pressure in the mist line, so the setting of that dial might pressure in the mist line, so the setting of that dial might
need adjustment.
• The best bet is to start by setting dial to 5 seconds. The best bet is to start by setting dial to 5 seconds. - If the
nozzles still spray and drizzle when the pump stops, nozzles still spray and drizzle when the pump stops,
increase the time the on dial to let more pressu increase the time the on dial to let more pressure escape
when the pump stops.
• If there is a long delay between when the pump starts and If there is a long delay between when the pump starts and
when the nozzles begin to spray, decrease the time on the when the nozzles begin to spray, decrease the time on the
dial, as the system is not keeping enough pressure in the as the system is not keeping enough pressure in the
mist line and it takes longer for the pump to fully mist line and it takes longer for the pump to fully
depressurize the line each time the pump starts. depressurize the line each time the pump starts.
• Some factors affecting the time required here are the Some factors affecting the time required here are the
material of the mist line, length of the mist line, number of
nozzles, and strength of the springs in the anti nozzles, and strength of the springs in the anti-drip valves
inside the nozzles.
• Turning On / Off the Misting System
• Press the power switch "On" & "Off" to start & stop • Press the power switch "On" & "Off" to start & stop
machine.
5. Pump stop running without water
• The "On" & "Off" indicator lights will be off even though ndicator lights will be off even though
the power switch is turned on. The misting system will stop the power switch is turned on. The misting system will stop
running automatically when the water supply to the pump running automatically when the water supply to the pump
is stopped.
• Important: Never attempt to run the pump without Never attempt to run the pump without
water. Please make sure the water supply is sufficient, then water. Please make sure the water supply is sufficient, then
re-start the pump.
left of "Stop Spraying
t line, number of
R M
OUTINE AINTENANCE SCHEDULE AINTENANCE SCHEDULE
Pump
Description Action
Pump Check Oil
Level
Filter Clean Every Every 15 days
Nozzles Clean
Pipes/Hoses Flush Every 15 days Every 15 days
Oil
Oil Drain Plug Oil Drain Plug
Typ
Volume
1. First 30~40 houres First 30~40 houres
Time
2. Every 100~200 houres of use Every 100~200 houres of use
GB
Frequence Frequen
Before every Before every
use
As necessary As necessary
Oil Inlet Cover
Oil Window
WM Series
SAE 30~40
80 cc