Quick A 312 Manuel De L'utilisateur page 17

POS. DESCRIPTION
15 Key
16 Key
17 Key
18A Chain guide cover A
18B Chain guide cover white F
18C Chain guide cover black F
19A Screw Aries
19B Screw Flair
20 Rope/chain stripper A-F base
21 Sensor
22 Screw for pressure lever
23A Black pressure lever
23B White pressure lever
24 Spring for pressure lever
25 Cover pin
26A Oval base Aries
26B Oval base white Flair
26C Oval base black Flair
27 Rope/chain stripper R base
28 Rider screw
29 Vite Rider
30 Gasket/ jig Aries-Flair-shaped
31 Gasket / jig Rider
32A Studs Aries base
32B Studs Flair base
33 Gearbox flange gasket
TOP 300/500W
34A Gearbox 300/500W Quick
34B Gearbox "Hi Speed" 500W Quick
35 Washer
36 Spring washer
37 Nut
38 Screw
39 Paper gasket
40 Key
41A Electric motor 300W 12V
41B Electric motor 500W 12V
41C Electric motor 500W 24V
42 Flange gasket 500W
43 Watertight
44 Poles gasket
45 Bottom protec cover 500W
46 Screw
AFR 300/500W - REV012A
CODE
MBH0606025X0
MBH0606050X0
Quick
MBH0606060X0
marine environments. In any case, any salt deposits on the outside
SGMSGG040000
must be removed periodically to avoid corrosion and damage to
PDGC04DW0000
the equipment. The parts where salt may have built up should be
PDGC04DB0000
washed thoroughly with fresh water.
MBV0516MXSC0
MBV0530MXSC0
Once a year, the drum and the gypsy are to be taken apart as
follows:
MSN04VX00000
SAKREED00000
DRUM VERSION
MSMVT0400000
Use the handle (1) to loosen the bush (3); pull off the drum (4) and
PDLVTD040000
the top clutch cone (5); loosen the fixing screws (19 or 29) of the
PDLVTD04W000
rope/chain stripper (20 or 28) and remove it. Pull off the gypsy (6).
MMTND0400000
MSR04X000000 NO-DRUM VERSION
Use the handle (1) to remove the gypsy cover (2); remove the top
SGMSC04V0000
clutch cone (5); loosen the fixing screws (19 or 29) of the rope/chain
SMPD04VW0000
stripper (20 or 28) and remove it and pull off the gypsy (6).
SMPD04VB0000
SGMSC04C0000
Clean all the parts removed to avoid corrosion, and grease the shaft
MSN04CX00000
thread (13 and 14) and the gypsy (6) where the clutch cones (5) rest
MBV0616MXTSC (use grease suitable for marine environment).
PGBSV0400000
Periodically grease the hinge pin (25) of the inspection door (only
PGBSC0400000
windlasses with aluminium bases).
MBP080607X00
MBP080608X00
Remove any oxide deposits from the terminals of the electric motor
and the reversing contactor unit; grease them.
PGFLRDTG4000
MR0400000000
MR05AFHS0000
MBR08X000000
MBR08XDE0000
MBD08MXEN000
MBV0516MXE00
PGBMR0400000
MBH040415F00
EMF031200000
EMF051200000
EMF052400000
PGGPMFN04000
PCCCPM040000
PGGPMPM04000
PCCPPMFN0400
MBV03916AXCC
MAINTENANCE
WARNING: make sure the electrical power to the motor
is switched off when working manually on the windlass.
Carefully remove the chain or rope from the gypsy or the
rope from the drum.
® windlasses are manufactured with materials resistant to
GB
17