Evolution POWER TOOLS FURY3 Manuel D'instruction page 5

Table des Matières

Publicité

recommended leg set. The base of the saw has four holes to mount the
mitre saw. If the saw is to be used in one location, permanently fasten it to
the workbench or leg set.
1.
Tighten the sliding rail, mitre and bevel locks.
2.
Place the saw so other people cannot stand behind it. Thrown debris
could injure people in its path.
3.
Place the saw on a firm, level surface where there is plenty of room
for handing and properly supporting the workpiece.
4.
Support the saw so the table is level and the saw does not rock.
5.
Bolt or clamp the saw to its support.
INSTALLING OR REMOVING THE BLADE
WARNING: Only use genuine Evolution blades which are designed for this
machine. Note: Remove the plug from the power supply.
1.
Ensure cutting head is up.
2.
Remove the guard retaining clip. (Fig. 1)
3.
Press safety lock button in and lift up the lower blade guard. (Fig. 2)
4.
Press the black lock button to lock the arbor. (Fig. 3)
5.
Using the supplied spanner, release the arbor screw to remove the
blade. (Fig. 4)
6.
Install the new 210 mm (8-1/4") blade. Make sure the rotation arrow
on the blade matches the clockwise rotation arrow on the upper
guard. The blade teeth should always point downward at the front of
the saw.
7.
Install the blade washer and arbor screw.
8.
Turn box spanner to secure the blade.
9.
Tighten arbor screw using moderate force, but do not overtighten.
10. Replace the guard retaining clip. (Fig. 1).
11. Ensure the spanner is removed before operating the machine.
ADJUSTMENT OF THE CUTTING ANGLES.
MITRE ANGLE: (Fig. 5)
1.
Loosen the sliding rail locking knob, push the saw handle back
as far as it will go and lock the handle.
2.
Loosen the mitre angle lock knob.
3.
Pull up the angle set lever and turn the table until the angle pointer
reach to the desired angle on angle mitre guide (fig 5).
4.
Tighten the mitre angle lock knob.
BEVEL ANGLE: (Fig. 6)
1.
Lock the cutting head down with the cutting lock knob.
2.
Loosen the bevel lock.
3.
Adjust angle until the bevel angle point reaches the desired bevel
angle.
4.
Tighten the bevel lock.
FITTING THE REPEAT STOP
1.
Loosen the thumb screws to allow the arms of the workpiece
support into the holes in the repeat stop.
2.
Tighten the thumb screws firmly to minimize movement on the
workpiece support.
3.
Attach the workpiece support as detailed below.
NOTE: By loosening the thumb screws the repeat stop can be
adjusted to required widths for each application.
FITTING THE WORKPIECE SUPPORT (Fig.7)
1.
Loosen the support retaining screw located on the turntable.
2.
Insert the workpiece support into the retaining holes in the base.
3.
Tighten the retaining screw.
FITTING THE UPPER WORKPIECE CLAMP (Fig.8)
1.
Fit the clamp to the retaining hole that best suits the cutting
application, ensuring that it is fully pushed down.
2.
Tighten the thumbscrew to lock the pillar.
3.
Put the workpiece to be cut onto the saw bed.
4.
Adjust the clamp so that it securely holds the workpiece.
FITTING THE FRONT WORKPIECE CLAMP (Fig.8a)
1.
Fit the clamp to the retaining hole that best suits the cutting
application.
2.
Put the workpiece to be cut onto the saw bed.
3.
Adjust the clamp so that it securely holds the workpiece.
NOTE: A combination of upper and front clamp should be used which best
secures the workpiece.
DEPTH STOP (Fig. 9)
Use of the depth stop feature means that the blade will not cut completely
5

Publicité

Table des Matières
loading

Table des Matières