Preface; Using This Manual; Pictograms And Symbols; Introduction - PLYMOVENT DRAFTMAX BASIC Manuel D'installation

ENGLISH

PREFACE

Using this manual

This manual is intended to be used as a work of reference for
professional, well trained and authorised users to be able to
safely install, use, maintain and repair the product mentioned
on the cover of this document.

Pictograms and symbols

The following pictograms and symbols are used in this manual:
TIP

Suggestions and recommendations to simplify
carrying out tasks and actions.
ATTENTION!
A remark with additional information for the user. A
remark brings possible problems to the user's
attention.
CAUTION!
Procedures, if not carried out with the necessary
caution, could damage the product, the workshop or
the environment.
WARNING!
Procedures which, if not carried out with the necessary
caution, may damage the product or cause serious
personal injury.
WARNING!
Denotes risk of electric shock.
WARNING!
Important warning to prevent fire.
Service and technical support
For information about specific adjustments, maintenance or
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. He will always be willing to
help you. Make sure you have the following specifications at
hand:
- product name
- serial number
You can find these data on the identification plate.
1

INTRODUCTION

1.1

Identification of the product

The identification plate contains, among other things, the
following data:
• product name
• serial number
• supply voltage and frequency
• power consumption
1.2

General description

The downdraft table is a workbench with an integrated
extraction fan and filtration system that is used for welding,
grinding, and plasma cutting applications. Depending on the
specific application, the use of certain accessories is required
and/or recommended (refer to section 1.3).
The downdraft table features a work grid, a three-stage pre-
filtration system for optimum spark arresting and two oval main
filter cartridges. Both pre and main filters have dust drawers
underneath. The working height of the downdraft table is
adjustable.
1.2.1 DraftMax Basic
The main filter cartridges of the DraftMax Basic are disposable.
0507060400/151013/G DraftMax Basic | DraftMax Advance | DraftMax Ultra
1.2.2 DraftMax Advance
The main filter cartridges in the DraftMax Advance are self-
cleaning by means of a manually controlled compressed air
system.
1.2.3 DraftMax Ultra
The main filter cartridges in the DraftMax Ultra are self-cleaning
by means of an automatically controlled compressed air system.
1.3

Options and accessories

The following products can be obtained as an option and/or
accessory:
A Back panel.
The back panel consists of a sheet metal plate to be mounted
on the downdraft table.
B Backdraft kit (required for all welding and plasma cutting
applications and recommended for grinding applications).
The backdraft kit consists of narrowing plates to be mounted
underneath the workgrid and a backdraft panel with vertical
lamellas.
C Side panels.
The side panels consist of hinged trapezium-shaped sheet
metal plates and have to be used in combination with the
backdraft kit or back panel. They are to be mounted on the
sides of the downdraft table.
D Plasma cutting work grid (required for plasma cutting
applications).
Specially constructed work grid suitable for plasma cutting,
including additional perforated steel spark arresters.
E HEPA kit (required for stainless steel welding).
Consists of a filter housing with a HEPA filter to be mounted
on the outlet of the downdraft table. Filter surface area
2 2
34 m (366 ft ). Filter class: HEPA 11.
F Silencer/Outlet duct.
Consists of a rectangular sheet metal shaft to be mounted
on the outlet of the downdraft table or on the HEPA kit.
G Outlet connection plate
H Working light.
Lighting fixture with 18W fluorescent light to be mounted to
the back panel or backdraft panel.
I Movement sensor (DraftMax Ultra only).
Automatic start/stop based on movement sensor, to be
mounted on top of the back panel or backdraft panel.
J Welding cable sensor (DraftMax Ultra only).
Metal clamp with built-in sensor that works as an automatic
start/stop device. The clamp is to be connected to the mass
cable of the welding machine. Suitable for welding
applications only.
K Bench vice mounting bracket.
To be connected to the standard work grid of the downdraft
table (bench vice not included).
L Wheel set.
Consists of 5 swivel castors - 2 of which with brake - to be
mounted underneath the downdraft table.
M Dust tray lid (recommended for stainless steel welding).
Lid to cover the dust drawer underneath the main filter
cartridges. Comes with a plastic bag, a face mask, and a pair
of disposable gloves.
EN - 3