Determining Wall Plate Location - Frigidaire Gallery Série Instructions D'installation

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
C.
Plate position -beneath
cabinet
NOTE: IT IS VERY
READ AND FOLLO IMPOR
IN THE W THE TANT TO
BEFOR INSTA LLATIO DIREC
REAR E PROCE N INSTR UCTIO TIONS
WALL TEMPL EDING WITH THIS NS
This Rear Wall Template ATE. 3/8" TO EDGE
outlet. mounting plate and serves 12"
1. Use to locate the horizonta to position the bottom
accuratel a level to check l exhaust
2. Locate y. that the template
right side and mark at least is positione d  
 of the centerline one stud on the left 4"  
screw mounted It is important to use at . or    
of the microwav firmly in a stud to least one wood   
locations for the supplied e. Mark two additiona support the weight   
3. Drill holes in the marked toggle bolts. l, evenly spaced     Trim the
a stud, drill a 3/16" locations rear wall templa
that do toggle bolts. not line up with hole for wood screws. . Where there is  te along
 a stud, drill 5/8" For holes  the dotted
AT THIS DO NOT INSTALL holes for  
4. Remove TIME. THE MOUNTI  
5. Review the template NG PLATE  
installatio the Installatio from the n Instructio rear wall.
n situation. n book for your
Darle vuelta
versión a la hoja para consulta
en Español . r la
 
Locate and mark    
mounti ng plate. holes to     
IMPOR align with holes in      
TANT: the       
LOCAT E AT LEAST  
THE CENTE ONE STUD  
MARK RLINE . ON EITHE
THE LOCAT R SIDE     
SPACE D TOGG ION FOR OF
AREA. LE BOLTS 2 ADDIT IONAL
IN THE MOUN , EVENL Y    
TING PLATE
  
Trim the
rear wall
templa te along
the dotted
line.

Locate
and mark
 mounti ng plate. holes to align with
IMPOR holes in
LOCAT TANT: the
E AT LEAST
THE CENTE ONE STUD
MARK RLINE . ON EITHE
SPACE THE LOCAT R SIDE OF
D TOGG ION FOR 2 ADDIT
 AREA. LE BOLTS IONAL
IN THE MOUN , EVENL Y
TING PLATE

C
Plate position -beneath recessed
bottom cabinet with front overhang
NOTE : IT IS
READ VERY IMPOR
IN THE AND FOLLO TANT
BEFO INSTA LLATI ON W THE DIREC TO
REAR RE PROC INSTR TIONS
WALL EEDIN G WITH UCTIO NS
This Rear TEMP LATE. THIS 3/8" TO EDGE
mounting plate and Wall Template serves
outlet. to locate to position 12"
1. Use a level the horizonta l exhaust the bottom
2. Locate accurate ly. to check that the
and mark template is positione
 right side of the centerlin at least one stud d 4"  
screw mounted I t is importan  e. on the left or  
of the microwa firmly in t to use at least    
locations ve. Mark a stud to support one wood  
3. Drill for the supplied two additiona the weight  
a stud, holes in the marked toggle bolts. l, evenly spaced     Trim the
that do drill a 3/16" hole for locations . Where   rear wall
toggle not line up with wood screws. there is templ ate
  bolts. a stud, drill 5/8" For holes   along the dotted
AT THIS D O NOT INSTALL holes for   line.
4. Remove TIME. THE MOUNT  
5. Review the template the Installati from the ING PLATE  
installatio n situation on Instructio rear wall.
. n book for your
Darle vuelta
versión a la hoja para consult
en Españo l. ar la

Locate and mark  
mount holes to    
ing plate. align with      
IMPOR TANT: holes in       
LOCA TE AT the    
THE CENT LEAST   
ERLIN ONE STUD  
MARK THE LOCA E. ON EITHE       
SPAC TION FOR R SIDE OF
ED TOGG 2 ADDIT
AREA . LE BOLTS IN THE IONAL
MOUN , EVEN LY    
TING PLATE
   
Trim the
rear wall templ ate
along
the dotted
line.

 Locate and mark
mount ing plate. holes to
IMPOR align with
TANT: holes in the
LOCA TE AT
THE CENT LEAST ONE STUD
MARK ERLIN ON EITHE
THE LOCA E. R SIDE
SPAC ED TOGG TION FOR OF
 AREA LE BOLTS 2 ADDIT
. IN THE IONAL , EVEN
MOUN TING PLATE LY

C L
Installation Instructions
flat bottom
line.
2 " ²
16-1/2

Draw a vertical line on
the wall at the center of
the 30 " wide space.
Tape the Rear Wall
Template onto the wall
matching the centerline
and touching the
bottom of the cabinet.
Draw a line on the
back wall equal to the
depth of the front
overhang.
READ NOTE: IT IS VERY
IN THE AND FOLLOW INSTALLAT IMPORTAN THE DIRECTION T TO
BEFORE REAR PROCEEDI ION INSTRUCTI S
This Rear mounting Wall Template WALL TEMPLATE NG WITH . THIS ONS 3/8" TO EDGE
1. Use outlet. plate and to locate serves the horizontal to position the bottom 12"
2. Locate accurately. a level to check that the template exhaust
 right side and mark of the centerline. at least one stud is positioned 4"  
screw mounted of the microwave. It is important firmly in to use at least on the left or   
3. Drill locations for the supplied Mark two a stud additional, to support one wood the weight    
 that do a stud, holes in drill a 3/16" the marked toggle locations. bolts. evenly spaced  Trim the rear wall
 toggle bolts. not line up with hole for a stud, wood screws. drill 5/8" Where there is For holes   template along
4. Remove AT THIS TIME. DO NOT INSTALL THE MOUNTING holes for   the dotted line.
5. Review installation the template the Installation from the rear wall. PLATE  
situation. Instruction book for your
versión Darle vuelta a la hoja
en Español. para consultar la
Locate and mark   
mounting plate. holes to align with      
LOCATE IMPORTAN T: holes in the      
THE CENTERLIN AT LEAST ONE STUD  
MARK SPACED THE LOCATION E. ON EITHER SIDE OF     
AREA. TOGGLE BOLTS FOR 2 ADDITIONA
IN THE MOUNTING L, EVENLY   
PLATE
 
Trim the rear wall
template along
the dotted line.

 Locate and mark
mounting plate. holes to align with
LOCATE IMPORTAN T: holes in the
THE CENTERLIN AT LEAST ONE STUD
MARK SPACED THE LOCATION E. ON EITHER SIDE OF
 AREA. TOGGLE BOLTS FOR 2 ADDITIONA
IN THE MOUNTING L, EVENLY
PLATE


C
3 0 0 " 0
30
to Cooktop
Plate position
cabinet bottom
recessed
NOTE : IT IS VERY
READ IMPOR
IN THE AND FOLLO TANT
BEFOR INSTA LLATIO W THE DIREC TO
E PROC N INSTR TIONS
REAR WALL EEDIN G WITH UCTIO NS
This Rear TEMP LATE. THIS
mounting Wall Template 12"
outlet. plate and to locate serves to position
1. Use a level the horizonta l exhaust the bottom
accurate ly. to check that the
2. Locate and mark template is positione
right side of the centerline at least one stud d 4"  
  I t is importan . on the left or  
screw mounted t to use at least    
of the microwav firmly in a stud to one wood   
3. Drill holes locations for the supplied e. Mark two additiona support the weight
in the marked toggle bolts. l, evenly spaced
that do a stud, drill a 3/16" locations
toggle bolts. not line up with hole for wood screws. . Where there is 
  a stud, drill 5/8" For holes  
AT THIS D O NOT INSTALL holes for 
4. Remove TIME. THE MOUNTI
5. Review the template NG PLATE
installatio the Installatio from the rear wall.
n situation. n Instructio n book
for your
versión Darle vuelta a la hoja
en Español para consulta
. r la
Locate  
and mark    
mount ing holes to    
IMPOR plate. align with holes in  
TANT: the  
LOCAT E AT LEAST  
THE CENTE ONE STUD  
RLINE ON EITHE
MARK THE LOCAT . R SIDE     
SPACE ION FOR OF
AREA. D TOGG LE BOLTS 2 ADDIT
IN THE IONAL , EVENL    
MOUN TING PLATE Y
Trim the
rear wall templa
te along
the dotted
line.



C
Draw a vertical line on the wall at the center of the
30 " space.
Tape the Rear Wall Template onto the wall
matching the centerline and touching the bottom
cabinet frame.
Your cabinets may have decorative trim that
interferes with the microwave installation. Remove
the decorative trim to install the microwave properly
and to make it level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no
back or side frame, install the mounting plate down
the same distance as the front overhang depth. This
will keep the microwave level.
1 Measure the inside depth of the front overhang.
2
Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside
depth of the front overhang.
3
For this type of installation with front overhang
only, align the mounting tabs with this horizontal
line, not touching the cabinet bottom as described
in Step D.
EN-7
-beneath framed
3/8" TO EDGE
  
    Trim the rear wall
templa
te along
the dotted line.
 
 
 
   
   

 
   
Locate and mark
mount ing holes to
plate. align with
IMPOR TANT: holes in the
LOCAT
THE CENTE E AT LEAST
RLINE ONE STUD
MARK THE LOCAT . ON EITHE R SIDE
SPACE ION FOR OF
D TOGG 2 ADDIT
AREA. LE BOLTS IN THE IONAL , EVENL
MOUN Y
TING PLATE


3 0 0 " 0
30 to Cooktop