Milwaukee M18 FUEL Manuel De L'utilisateur page 3

• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acciden-
tally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
• Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging im-
properly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
SERVICE
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
COMPACT ROUTERS
• Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
• Always hold the tool firmly in your hand(s) dur-
ing the start-up. The reaction torque of the motor,
as it accelerates to full speed, can cause the tool
to twist.
• Maintain a firm grip on the power tool and po-
sition your body and arm to allow you to resist
kickback forces. The operator can control kick-
back forces, if proper precautions are taken.
• Some woods contain preservatives that can be
toxic. Take extra care to prevent inhalation and
skin contact when working with these materials.
Request, and follow, any safety information avail-
able from your material supplier.
• Never hold the workpiece in one hand and the
tool in the other hand when using the tool. Never
place hands near or below cutting surface.
Clamping the material and guiding the tool with
both hands is safer.
• Never use dull or damaged bits. Sharp bits
must be handled with care. Damaged bits can
break during use. Dull bits require more force to
push the tool, which could cause the bit to break.
Damaged bits can throw carbide pieces and burn
the workpiece.
• After changing the bit or making any adjust-
ments, make sure the collet nut and any other
adjustment devices are securely tightened.
Loose adjustment devices can unexpectedly shift,
causing loss of control. Loose rotating components
will be violently thrown. Watch for vibration or wob-
bling that could indicate an improperly installed bit.
• Never start the tool when the bit is in contact
with the material. The bit cutting edge may grab
the material causing loss of control of the tool.
• Never lay the tool down until the bit has come
to a complete stop. The spinning bit can grab the
surface and pull the tool out of your control.
• Never touch the bit during or immediately after
use. After use the bit, collet, and collet nut may be
hot enough to burn bare skin.
• Never clamp the workpiece to a hard surface,
such as concrete or stone. Contact with the bit
could cause the tool to jump and loss of control.
• Only operate the routers when held. Do not
clamp or secure the router to a surface and hold
the workpiece by hand.
• Never use bits larger than the smallest of the
openings in the base, sub-base, or dust collection
port.
• Do not loosen or remove the plunge base caps.
Internal springs are under pressure. If loosened or
removed, the plunge base caps and internal springs
will become projectiles, which could cause injury.
• To reduce the risk of injury, when
WARNING
working in dusty situations, wear
appropriate respiratory protection or use an
OSHA compliant dust extraction solution.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
SPECIFICATIONS
Cat. No. ....................................................2723-20*
Volts.............................................................. 18 DC
Battery Type .................................................M18™
Charger Type................................................M18™
No Load RPM ................................ 10,000 - 31,000
Maximum Bit Size .......................................... 1-1/2"
Collet Size ........................................................ 1/4"
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Plunge Base Cat. No. ......................... 48-10-5601
Offset Base Cat. No. ........................... 48-10-5602
*Comes with Fixed Base 31-06-0036
3