emerio WH-125971 Mode D'emploi page 10

OPEN WINDOW DETECTION
Note: This function can only be activated when the appliance is in heating mode or temperature setting
mode.
1. Press the open window detection button on the remote control. The temperature setting indicator light
flickers. The open window detection starts after 1 minute.
2. 10 minutes as a round. The appliance will take the temperature in the beginning of each round as a
checking reference, and check it every 5 minutes. If the temperature in the checking point decreases more
than 8 ℃ than the referenced temperature, the appliance will stop heating, send out alarm for 5 seconds.
Meanwhile the fan is working, the temperature setting indicator light and a code "OF" on LED flickers for
30 seconds, then the appliance goes into standby. In this case you could do by either way as follows.
1) Press the open window detection button to restart with the same working mode before the appliance
stops. The open window detection will then restart too.
2) Press the ON/Standby button, the appliance will enter into standby.
3. If in the checking point, the temperature decreases less than 8 ℃ compared to the referenced
temperature, the former is the same as or higher than the latter, the appliance will keep heating and the
open window detection will continue.
4. The maximum detection temperature is 51 ℃. The appliance will stop running automatically when it
detects the temperature reaches 51 ℃.
WEEK TIMER
Note:

This function can only be activated when the appliance is in heating mode or temperature setting mode.

When the week timer is set, the timer for entering into standby automatically will be inactive.
To use the week timer function, please follow below steps.
1. Press the week timer button. If this is the first start-up after the power switch is pressed to "I", you need to
set the current time first.
1) The LED displays "01", press "+" "-" to select the day. "01 – 07" stand for Monday to Sunday. Press "OK"
to confirm the setting. For example, it's Friday today, then you select "05".
2) The LED displays "00", press "+" "-" to set the hour. For example, the time now is 16:24, then you select
"16" here. Press "OK" to confirm the setting.
3) The LED displays "00", press "+" "-" to set the minute. For example, the time now is 16:24, then you
select "24" here. Press "OK" to confirm the setting.
Note: If you don't press "OK" within 10 seconds, the setting will fail.
2. After setting the current time, or this is a start from the standby mode, the LED display will show "P1",
which is the mode code. If this is not the mode you want, press the week timer button again and again to
choose a mode from "P2" to "P6". Appliance's working time is listed according to the different modes in
below table.
If you press the week timer button after the display of "P6", you will exit the setting of week timer.
Mode Monday
P1 8:00-17:00
a
P2 18:00-7:00
P3 8:00-17:00
a
P4 18:00-7:00
P5 OFF
P6 Free mode
Notes:
For P2/P4 Mode, the stop time is at the next day.
Tuesday Wednesday
8:00-17:00 8:00-17:00
a
18:00-7:00 18:00-7:00
8:00-17:00 8:00-17:00
a
18:00-7:00 18:00-7:00
OFF OFF
Free mode Free mode
Thursday Friday
8:00-17:00 8:00-17:00
a a
18:00-7:00 18:00-7:00
8:00-17:00 8:00-17:00
a a
18:00-7:00 18:00-7:00
OFF OFF
Free mode Free mode
- 9 -
Saturday Sunday
8:00-17:00 8:00-17:00
a a
18:00-7:00 18:00-7:00
OFF OFF
a
OFF OFF
00:00-23:59 00:00-23:59
Free mode Free mode
a