Lighting The Wine Cellar; Wine Cellar Care; Base Grille; Cleaning - Jenn-Air JUW24FRACX Guide D'utilisation Et D'entretien

5. Continue stocking each remaining rack as described in the
above steps.

Lighting the Wine Cellar

The wine cellar has an interior light that comes on any time the
door is opened. You may also choose to keep the light on at all
times by pressing the left side of the switch, located next to the
temperature control, on the base grille.
NOTES:
Leaving the light on for an extended period of time will slightly
increase the temperature of the wine cellar.
The light is an LED which does not need to be replaced. If the
LED does not illuminate when the door is opened, call Service
to replace the light. See Assistance or Service for contact
information.

WINE CELLAR CARE

Base Grille

You must remove the base grille to access the condenser coils for

cleaning.

To remove the base grille:
1. Open the wine cellar door.
2. Using a Phillips screwdriver, remove the two screws. Push
both tabs in toward the center to release the base grille from
the wine cellar.
A
3. Remove the base grille.
To replace the base grille:
1. Open the wine cellar door.
2. Position the base grille so that both tabs align and the base
grille snaps into place. Replace the two screws. Tighten the
screws.
B A
A. Tabs
B. Screws
Cleaning
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Clean the wine cellar about once a month to avoid buildup of
odors. Wipe up spills immediately.
To clean your wine cellar:
1. Unplug wine cellar or disconnect power.
2. Remove all racks from inside the wine cellar.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
To avoid damaging wooden tines and trim pieces, wipe
them off with a clean sponge or soft cloth and warm water.
Do not use detergent or immerse the entire rack into water
when cleaning.
Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners containing
chlorine. These can scratch or damage materials. Dry
thoroughly with a soft cloth.
NOTE: To keep your stainless steel wine cellar looking like
new and to remove minor scuffs or marks, it is suggested that
you use the manufacturer's approved Stainless Steel Cleaner
and Polish. To order the cleaner, see "Accessories."
IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry thoroughly with a soft cloth.
5. Replace the racks.
6. Clean the condenser coils regularly. They are located behind
the base grille. Coils may need to be cleaned as often as every
other month. This may help save energy.
Remove the base grille. See "Base Grille."
Use a vacuum cleaner with an extended attachment to
clean the condenser coils when they are dusty or dirty.
Replace the base grille.
7. Plug in wine cellar or reconnect power.
11