Service Parts - Broan-NuTone QTRE080H Mode D'emploi

INSTALL GRILLE (
6. Attach grille
to housing.
Squeeze grille
s p r i n g s a n d
insert them into
slots on each
side of housing.
7. Push grille
against
ceiling.
WARRANTY
BROAN-NUTONE CANADA INC.
THREE-YEAR LIMITED WARRANTY
Broan-NuTone Canada warrants to the original consumer purchaser of its
products that such products will be free from defects in materials or workmanship
for a period of three (3) years from the date of original purchase. THERE ARE
NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
During this three-year period, Broan-NuTone Canada will, at its option,
repair or replace, without charge, any product or part which is found to be
defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS
OR TUBES, BULBS OR BATTERIES, FILTERS, DUST, ROOF CAPS, WALL CAPS
AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a)
normal maintenance and service or (b) any products or parts which have been
subject to misuse, negligence, accident, improper maintenance or repair (other
than by Broan-NuTone Canada or an authorized representative), faulty installation
or installation contrary to recommended installation instructions.
The duration of an implied warranty is limited to the three-year period as
specifi ed for the express warranty.
BROAN-NUTONE CANADA'S OBLIGATION TO REPAIR OR REPLACE, AT
BROAN-NUTONE CANADA'S OPTION, SHALL BE THE PURCHASER'S SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE CANADA
SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR
PERFORMANCE. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone Canada at
the address or telephone number stated below, (b) give the model number
and part identifi cation and (c) describe the nature of any defect in the product
or part. At the time of requesting warranty service, you must present evidence
of the original purchase date.
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest Broan-NuTone Canada Inc. dealer:
Dial Toll Free: 1-888-882-7626
Please be prepared to provide:
• Product model number • Date and proof of purchase
• The nature of the diffi culty
Broan-NuTone Canada Inc. 1140 Tristar Drive, Mississauga, Ontario L5T 1H9
REPLACEMENT PARTS AND REPAIRS:
In order to ensure your unit remains in good working condition, you must use Broan-NuTone genuine replacement parts only. Broan-NuTone genuine
replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certifi cation standards and maintain a high
standard of safety. Any third party replacement part used may cause serious damage and drastically reduce the performance level of your unit, which
will result in premature failing. Broan-NuTone also recommends to contact a Broan-NuTone certifi ed service depot for all replacement parts and repairs.
' )
CONT D
MODELS QTRE080H • QTRE100H
QTREN080H • QTREN100H

SERVICE PARTS

BL0017A
No. Part No. Description
1 97016466 Housing
2 97016449 Duct Connector 4"
3 98010102 Wiring Plate
4 99170245 Screw no. 8-18 x .375" (2 req'd)
5 10941326 Wire Panel/Harness Assembly
10941327 Motor/Blower Wheel Assembly
QTRE080H & QTREN080H*
6
Motor/Blower Wheel Assembly
10941328
QTRE100H & QTREN100H
10941329 Motor Plate/Control Assembly
QTRE080H & QTREN080H*
7
Motor Plate/Control Assembly
10941330
QTRE100H & QTREN100H
10941331 Blower Assembly QTRE080H
10941332 Blower Assembly QTRE100H
(includes keys 6 & 7)
*
10941333 Blower Assembly QTREN080H
10941334 Blower Assembly QTREN100H
(includes keys 6 & 7)
8 30260045 Flanged Nut no. 8-32 (4 req'd)
97018314 Grille Assembly (includes key no. 10)
QTRE080H & QTRE100H
9
97017934 Grille Assembly (includes key no. 10)
QTREN080H & QTREN100H
10 99140199 Grille Spring (2 req'd)
11 99111293 Spacer (2 supplied)
12 97016909 Hanger Bar Kit
*Not shown.
Order service parts by "Part No." - not by "Key No."
4
SERVICE NOTE
To remove Blower Assembly:
Unplug motor.
Remove screw (4) from motor
plate fl ange.
Find the single TAB on the motor
plate (located next to the receptacle).
Push up near motor plate tab while
pushing out on side of housing. Or
insert a straight-blade screwdriver
into slot in housing (next to tab) and
twist screwdriver.