Technical Data; Before Starting The Equipment - EINHELL GE-CH 1855/1 Li Mode D'emploi D'origine

4. Technical data

Cutter rail length ..................................... 620 mm
Cutting length ......................................... 550 mm
Tooth spacing ........................................... 18 mm
Cuts/min ...................................................... 2200
Charging time ..................................... ca. 40 min.
Sound pressure level, L
Sound power level, L
WA
K uncertainty ................................................. 3 dB
Interchangeable battery ......18 V d.c. / 2000 mAh
.............................(optional 18 V d.c. / 1500 mAh)
.............................(optional 18 V d.c. / 3000 mAh)
.............................(optional 18 V d.c. / 4000 mAh)
.............................(optional 18 V d.c. / 5200 mAh)
......................................... ≤ 2.5 m/s²
Vibration a
hv
K uncertainty .............................................. 1.5 dB
Weight ........................................................2.4 kg
Battery charger
Mains voltage ....................200-260 V ~ 50-60 Hz
Output voltage/current .................. 21 V d. c. / 3 A
The machine may exceed 85 dB (A). The operator
will require noise protection measures if this is
the case. The noise was measured in accordance
with EN 60745-1. The value of the vibrations emit-
ted by the handle was determined in accordance
with EN 60745-1.
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
Anl_GE_CH_1855_1_Li_SPK7.indb 18 Anl_GE_CH_1855_1_Li_SPK7.indb 18
GB
........................ 64.8 dB
pA
............................ 84.8 dB
- 18 -
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.

5. Before starting the equipment

Fitting the hand guard
Attach the hand guard (Fig.1/Item 2) in the di-
rection of the arrow as shown in fi gure 4a. Next,
fasten this with the 2 screws (Fig. 1/Item 10) as
shown in Fig. 4b.
Assembly of the steady grip
Attach the steady grip (Fig. 2/Item 3) in the direc-
tion of the arrow as shown in Fig. 4c.
Important: The lock (Fig. 4c/Item 11) must be on
the right-hand side! Make sure that the electrical
contacts are connected correctly.
Then fully tighten the screw (Fig. 4d/Item 12) with
the lock closed (Fig. 4c/Item 11).
Adjustable steady grip
The steady grip is adjustable. Loosen the lock
(Fig. 4c/Item 11) by opening, bring the steady grip
into the desired position and attach it again by
closing the lock (Fig. 4c/Item 11).
Swivel handle
The hedge trimmer is fi tted with a rear swiveling
handle. It can be swiveled 90° to the left and right.
To do so, pull the slide (Fig. 13/Item 10) in the di-
rection indicated by the arrow and turn the handle.
To return the handle to its original position you
must pull the slide (Fig. 13/Item 13) in the direc-
tion indicated by the arrow again. The handle
should be turned through 90° for vertical cuts.
Fitting the cuttings collector (Fig. 5a-5d)
For horizontal cutting we recommend that you
install the cuttings collector. This enables you
to remove the cuttings easily. The surface of the
hedge thus remains clear (Fig. 5a/5b). Position
the cuttings collector (14) on the cutter rail (Fig.
5c). Then push the cuttings collector as far as
possible towards the tip of the cutter rail and
secure it with the fastening screws (15) (Fig. 5d).
The cuttings collector can be fi tted on either the
right or left side.
Installing the battery (Fig. 4e)
Press the side pushlock buttons of the battery
pack as shown in Fig. 4e and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 1, make sure that the
12.07.2016 11:32:56 12.07.2016 11:32:56