Operation; Cleaning, Maintenance And Ordering Spare Parts - EINHELL TC-LL 2 Traduction Du Mode D'emploi D'origine

•
Close the battery compartment cover (6)
again, making sure that it locks securely
•
If the LED indicator flashes red continuously
even though the device is upright, this means
that the batteries are flat. Replace them as
described above.
5.2 Using the universal clamp (Fig. 3/Item 8)
You can fasten the supplied universal clamp (8)
to a table, shelf or similar object by clamping it in
position.
To fi t the equipment to the universal clamp,
proceed as follows:
•
Place the equipment by the female thread (7)
on the base of the equipment onto the male
thread (10) of the universal clamp (8)
•
Screw the equipment to the mounting with the
help of the wheel
•
Using the adjusting screw (9) and the ball
joints (a), you can tilt the equipment to the
angle you require
To disassemble, proceed in reverse order

6. Operation

6.1 Switching On/Off (Fig. 1)
Switching on:
•
Place the laser on a flat surface or fit it to the
universal clamp and fasten it as described in
5.2.
•
To switch the laser on, push the On/Off switch
to the left (viewed from the front). The lasers
switch on, the green LED (4) comes on and
the pendulum will no longer be blocked,
which means the laser can be aligned.
•
Press the button (5) to display or hide the
vertical or horizontal lines again individually.
Switching off :
To switch off , push the On/Off switch back to
the position on the right (viewed from the front).
The lasers switch off and the pendulum will be
blocked.
Important!
To prevent damage during transport or storage,
the equipment must always be switched off as
described above.
Anl_TC_LL_2_USA_SPK7.indb 9 Anl_TC_LL_2_USA_SPK7.indb 9
EN
6.2 Automatic alignment of the laser (Fig. 4)
After the laser has been switched on with the On/
Off switch (1), the lasers are aligned automatically
by the pendulum so that the vertical and
horizontal lines are displayed level on the wall.
(See Fig. 4)
Press the button (5) to display or hide the vertical
or horizontal line individually.
Important!
Make sure that the equipment is never tilted
more than 4 degrees or stands at an angle.
If this is the case, the laser beams will fl ash
and the LED (4) will light up red.
6.3 Manual alignment of the laser (Fig. 5)
The laser can also be aligned manually, to enable
a diagonal line to be displayed. Proceed as
follows:
•
Place the laser on a flat surface or fit it to the
universal clamp and fasten it as described in
5.2.
•
To switch the equipment on, push the On/Off
switch (1) to the left (viewed from the front).
•
Wait until the lasers are aligned and then
move the On/Off switch (1) back to the right.
•
Now press the button (5). The lasers switch
on and the LED (4) lights up red, because the
pendulum is blocked.
•
Now you can tilt the laser to the angle you
require, so that the lines are displayed
diagonally on the wall. (See Fig. 5)
•
Press the button (5) to hide or display the
vertical or horizontal line individually or to
switch the equipment off again.
7. Cleaning, maintenance and
ordering spare parts
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
- 9 -
03.04.2019 08:45:09 03.04.2019 08:45:09