EINHELL TE-MS 18/210 Li Traduction Du Mode D'emploi D'origine page 20

6.4 Miter cut 0°- 45° and turntable 0° (Fig. 1-3,
12)
The crosscut saw can be used to make miter cuts
of 0- 45° in relation to the work face.
•
If necessary, dismantle the clamping device
(8) from the left side of the saw table (18) or
mount on the right-hand side of the fixed saw
table (18).
•
Move the machine head (4) to its upper
position.
•
Fasten the turntable (17) in 0° position.
•
Set the miter angle on the machine head as
described in 5.5.
•
Cut as described in section 6.2.
6.5 Miter cut 0°- 45° and turntable 0°- 45° (Fig.
1-3, 13)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° in relation to the work surface,
with simultaneous setting of the turntable from
0°-45° to the left or 0°-45° to the right in relation to
the stop rail (double miter cut).
•
If required, dismantle the clamping device
(8) or mount on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper
position.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Use the handle (1) to adjust the turntable (17)
to the angle required (in this connection see
also section 6.3).
•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
and the stop rail as described in section 5.5.
•
Cut as described in section 6.2.
6.6 Limiting the cutting depth (Fig. 3)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do so, undo the nut
on the knurled screw (27). Turn the screw (27)
in or out to set the required cutting depth and
then retighten the knurled nut on the screw
(27).
•
Check the setting by completing a test cut.
6.7 Sawdust bag (Fig. 2)
The saw is equipped with a sawdust bag (22).
The sawdust bag (22) can be emptied by means
of a zipper at the bottom. Press the spring washer
of the sawdust bag such that it can be pushed
onto the extractor connection (43) of the machine.
Anl_TE_MS_18_210_Li_SPK7_USA.indb 20 Anl_TE_MS_18_210_Li_SPK7_USA.indb 20
EN
6.8 Replacing the saw blade (Fig. 1, 14)
•
Danger! Remove the rechargeable battery
before you replace the blade.
•
Wear work gloves to prevent injury when
changing the saw blade.
•
The hex key (39) is kept on the transport
handle.
•
Press the spindle locking system (5) with one
hand while positioning the hex key (39) on
the flange bolt (31) with the other hand. The
spindle locking system (5) engages after no
more than one rotation.
•
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
•
Turn the flange screw (31) right out and
remove the external flange (32).
•
Take the blade (7) off the inner flange and pull
out downwards.
•
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
•
Fit and fasten the new saw blade (7) in
reverse order.
•
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12) in both perpendicular and
45° angle settings.
•
Important! The work to change and align the
saw blade (7) must be carried out correctly.
6.9 Transport (Fig. 1-3)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Activate the release button (3), press the
machine head (4) downwards and secure
with the safety pin (25). The saw is now
locked in its bottom position.
•
Carry the machine by the fixed transport
handle.
•
To set up the equipment again, proceed as
described in section 5.2.
- 20 -
05.08.2019 14:05:52 05.08.2019 14:05:52