Indesit WT 102 Mode D'emploi Et D'installation page 35

Installation and removal
When the When the
When the
When the When the
appliance arrives appliance arrives
appliance arrives
appliance arrives appliance arrives
Whether new or just transported to a new house, installation is extremely
important for the correct functioning of your washing machine.
After removing the appliance
from its packaging, check that
it is intact. If in doubt, contact
a qualified technician
The inside of the The inside of the
immediately. The inside of the The inside of the The inside of the
machine is blocked, for machine is blocked, for machine is blocked, for machine is blocked, for machine is blocked, for
transportation, by four transportation, by four
transportation, by four transportation, by four transportation, by four
screws and rubber washers screws and rubber washers screws and rubber washers screws and rubber washers screws and rubber washers
on the back panel. on the back panel. on the back panel.
on the back panel. on the back panel.
Unblocking: remove Unblocking: remove Unblocking: remove Unblocking: remove Unblocking: remove
the 4 screws! the 4 screws! the 4 screws! the 4 screws! the 4 screws!
2
1
Before using the washing
remove remove
machine, remove remove remove
screws screws screws screws screws, remove the rubber
washers with the relative
spacer (keeping all the parts)
and use the plastic tabs
provided to fill in the holes.
Warning: should the screws Warning: Warning:
Warning: Warning:
be re-used, make sure you
fasten the shorter at the top.
Levelling Levelling Levelling
Levelling Levelling
The washing machine must be
levelled appropriately in order to
guarantee its correct functioning.
T T T T T o le o le o le vel the appliance, , , , , the f vel the appliance vel the appliance the f the f
o le o level the appliance vel the appliance the feet the f
must be adjusted must be adjusted must be adjusted must be adjusted; the angle of must be adjusted
inclination, measured according
to the worktop, must not exceed
2°. When placed on fitted carpet,
make sure the ventilation is not
obstructed within its surroundings.
The feet are adjustable.
Do not throw the blocking
screws and the spacers
away. In the event of a
removal, they can be used
to block the components
inside the appliance again
and so protect it during
transport.
Connection to the water Connection to the water Connection to the water Connection to the water Connection to the water
mains mains mains mains mains
Water pressure must range
within the values indicated on
the data plate on the rear of
your washing machine.
Connect the inlet
(situated unassembled inside
the drum) to a cold water tap
with a 3/4 gas threaded mouth.
If the water pipes are new or
left unused, run the water until
it is clear and free of debris.
Attach the hose to the
appliance, in line with the
appropriate water pipe inlet at
the top right.ù
the the
the the the
Water hose inlet to be fitted to
the top right.
Connecting the drain hose Connecting the drain hose Connecting the drain hose
Connecting the drain hose Connecting the drain hose
On the back of the appliance,
towards the top, you will find a
hook onto which you should
fasten the drain hose if
eet eet
eet eet
necessary. Insert the other end
in a wall draining duct or place
it on the edge of a sink or tub
avoiding excessive kinks and
It should be placed It should be placed
bending. It should be placed It should be placed It should be placed
at a height ranging from 60 to at a height ranging from 60 to at a height ranging from 60 to at a height ranging from 60 to at a height ranging from 60 to
100 cm. 100 cm.
100 cm. 100 cm. 100 cm.
In case it is necessary to fix the
end of the hose at a height
below 60 cm from the ground,
it must be fixed in the
appropriate hook placed on
the back panel as mentioned
above.
hose
The hook to be used in case the
drain hose ends at a height
below 60 cm.
If the hose drains into a tub or
sink, apply the plastic guide
and tie it to the tap.
The guide for draining into tubs
and sinks.
The hose must never The hose must never The hose must never
The hose must never The hose must never
remain immersed in water remain immer remain immer remain immer remain immer sed in water sed in water sed in water. . . . . sed in water
Extensions are inadvisable. In
case of absolute need, the
extension must have the same
diameter as the original hose
and must not exceed 150 cm
in length. In case of wall
draining pipes, their efficiency
must be checked by a qualified
technician. If the dwelling is on
one of the upper floors of a
building, there may be drain
trap problems causing the
washing machine to load and
unload water continuously.
In order to avoid such an
inconvenience, special anti-
drain trap valves are available
in shops.
Electric connection Electric connection Electric connection
Electric connection Electric connection
Before connecting the
appliance to the electric
socket, be sure that:
1) the electric socket is able
to sustain the appliance's
maximum power load
indicated on the data plate
and in compliance with the
law;
2) the supply voltage is
included within the values
indicated on the data
plate;
3) the socket is compatible
with the appliance's plug.
If not, do not use adapters,
but replace either the
socket or the plug;
4) electric household appli-
ances must be equipped
with an "earthing" system,
5) that the machine is not
placed on top of the power
supply cable once the
connection has been
made.
Warning!
Any modifications made to the
factory settings or an irregu-
lar electric connection, any
electrical, mechanical or hy-
draulic modification whatso-
ever to the appliance shall
render the guarantee invalid
and shall relieve the manufac-
turer and retailer of any and
all liability.
Plastic bags, polystyrene
foam, screws and other
packaging parts are not
children's toys, and are
potentially dangerous.
Instructions for installation and use
2 2 2 2 2