Menu Settings - Indexa DVT50 SET Mode D'emploi

To pair a second mobile unit with a doorbell button of the DVT50/2 SET
door intercom (channel No. 1), proceed as described above (DVT50
SET), except for the last point:
!
Press the pairing button [28] on the intercom unit, until a ringing
sound can be heard.
!
Immediately press the doorbell button you wish to pair. The
selection is confirmed by a flashing of the respective doorbell
button.
!
To pair a mobile unit with a second door intercom, select channel
No. 2.
Information about operation following extension:
!
If there is a ring at one of two door intercoms, you can see at the
top left of the camera image where the ring has come from: door
intercom "1#" or "2#".
!
When there is a ring at one of the door intercoms, all of the paired
mobile units that are switched on respond as described in section
11.1.
!
If there is a ring at a door intercom and the conversation is
accepted on one of two paired mobile units, the camera image
switches off on the other mobile unit, the start screen appears on it
and the screen switches off after approx. 20 seconds.
13. Settings
13.1 Settings adjusted directly by the buttons on the
mobile unit
Volume of the ring tone on the mobile unit
!
Press any button [1/2/3/5/7/8] on the mobile unit to make the
start screen appear.
!
Pressing the and
volume of the ring tone on the mobile unit.
Screen brightness
!
Press any button [1/2/3/5/7/8] on the mobile unit to make the
start screen appear.
!
Pressing the and
brightness of the screen.

13.2 Menu settings

Scrolling through the menu
!
To open the menu, first press any button [1/2/3/5/7/8] on the
mobile unit to make the start screen appear, then press the left
—
button [3 - "Menu"]. The menu items appear underneath
one another.
!
By pressing the and [2] buttons, you can scroll between the
menu items and through the sub-menu of a menu item.
!
To select a menu or sub-menu item, press the left button
"Select"].
!
By pressing the and
existing setting.
34 - GB
[2] buttons reduces or increases the
[2] buttons increases or reduces the
[2] buttons, you can change the
!
To return to the menu from a menu item or to close the menu,
press the right button
!
Approx. 15 seconds after a button is pressed, the menu closes
automatically.
VOLUME of the ring tone / conversation / ring and camera display
duration on the mobile unit
Talking Volume
Ringtone Volume Setting for the ring tone volume on the
Ringing Time
BRIGHTNESS
Setting the screen brightness (1 to 9 bars)
Factory setting: 3 bars
KEY TONE
Activation (ON) and deactivation (OFF) of the confirmation tone each
time a button is pressed
Factory setting: ON
RING TONE
Selection of the mobile unit ring tone (from 3 tunes)
Factory setting: Ring Tone 1
SNAP SET
Activation (ON) and deactivation (OFF) of automatic saving of a
snapshot when the ring button [25] on the door intercom is pressed.
The snapshot is saved on the mobile unit.
Factory setting: ON
SNAP SHOW
!
By pressing the
the snapshots.
!
To delete the snapshot currently shown on the screen, press the
—
[3 -
left button
—
[3 -
!
To delete all the snapshots saved on the mobile unit, press the
door release button
—
[7 - "Back"].
Setting for the loudspeaker volume on the
mobile unit (1 to 9 bars)
Factory setting: 6 bars
mobile unit (1 to 9 bars)
Factory setting: 6 bars
Setting for
B
the duration of the ring tone on the mobile
unit between 0 and 30 seconds. A setting of 0
seconds means that the ring tone is switched
off.
B the camera display duration
30 seconds. A setting between 1-14 seconds
will automatically set the duration to 15
seconds
Factory setting: 30 seconds
of the screen
- snapshot activation
- view/delete snapshots
and [2] buttons, you can scroll through
—
[3 - ] and confirm by pressing the left button
] again.
[5] and confirm by pressing the left
between 15 and