Product Specifications; Technical Data; Noise/Vibration Information - F.F. Group RH 2-26 PLUS Notice Originale

8 | English
protect against electric shock in the event of
failure of the basic insulation.
GUIDELINES FOR USING EXTENSION CORDS
Make sure your extension cord is in good condition.
f
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Always replace a damaged extension cord or have it
f
repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
f
excessive heat and damp/wet areas.
Use a separate electrical circuit for your tools. This
f
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same
as the voltage stamped on the motor nameplate.
Running at a lower voltage will damage the motor.

PRODUCT SPECIFICATIONS

INTENDED USE
The machine is intended for hammer drilling in
concrete, brick and stone. It is likewise suitable for
drilling without impact in wood, metal, ceramic and
plastic.

TECHNICAL DATA

Article number
Model RH PLUS
Rated voltage
Rated power input
No-load speed
Impact rate
Impact energy
Chuck type
Weight
Sound emission values determined according
to EN 60745-1, EN 60745-2-6
Typically the A-weighted noise levels of the product
are:
Sound pressure
dB(A)
level
Sound power level dB(A)
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60745-1, EN 60745-2-6
Vibration level max:
a
h
K

NOISE/VIBRATION INFORMATION

The vibration emission level has been measured
45 332 45 333
2-26 2-26 FC
V 230
Hz 50
W 850
min 0-1.100
-1
min 0-4.800
-1
J 2,6
SDS PLUS
kg 2,9 2,9
91,32
102,32
dB 3
(triax vector sum)
h
m/s 14,059
2
m/s 1,5
2
RH 2-26 PLUS | RH 2-26 FC PLUS
in accordance with a standardized test given in EN
60745-1; it may be used to compare one tool with
another and as a preliminary assessment of ex-
posure to vibration when using the tool for the
applications mentioned.
The vibration emission during actual use of the
power tool can differ from the declared total
value depending on the ways in which the tool
is used. There is the need to identify safety mea-
sures to protect the operator that are based on
an estimation of exposure in the actual conditions
of use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
WARNING! This machine produces an electro-
magnetic field during operation. This field may
under some circumstances interfere with active
or passive medical implants. To reduce the risk
of serious or fatal injury, we recommend persons
with medical implants to consult their physician
and the medical implant manufacturer before op-
erating this machine.
IDENTIFICATION
1. SDS - plus chuck
2. Tool holder (SDS - plus)
3. Dust protection cap
4. Locking sleeve
5. Depth stop
6. Auxiliary handle
7. Operational mode selection switch
8. Forward/reverse function lever
9. Lock-on button
10. On/Off switch
11. Drill chuck (45333)
BEFORE USE
Be careful of hidden electrical lines or gas and wa-
ter pipes. Check the working area, e.g. with a metal
detector. Always use the correct supply voltage!
The voltage of the power source must agree with
the value given on the nameplate of the machine.
TOOL CHANGING
Take care that the dust protection cap (3) is not
damaged when changing tools.
SDS - Plus Tools
The SDS - plus tool is designed to be freely mov-
able. This causes eccentricity when the machine is
offload. How ever, the drill automatically centers
itself during operation. This does not affect drill-
ing precision.
Inserting
Clean and lightly grease the tool before inserting.
Insert the dust-free tool into the tool holder (2)
with twisting manner until it latches. The tool
locks itself. Check the locking by pulling on the
tool.
Removing
Pull the locking sleeve (4) to the rear and hold
while removing the tool.
PUTTING INTO OPERATION
Switching on: Press the on- off switch (10)
f