Publicité
Les langues disponibles
Les langues disponibles
Battery charging with (optional) battery charger
installed on the machine
1.
For lead batteries only:
– check the electrolyte level inside the batteries; if
necessary top up through the caps (9, Fig. J);
– When the correct level is reached, close the caps (9)
and clean (if necessary) the upper surface of the
batteries.
2.
Connect the battery charger cable (31, Fig. C) to the
electrical mains (voltage and frequency must be
compatible with the battery charger values on the
machine serial number plate).
When the battery charger is connected to the mains, all
machine functions are automatically cut off.
If the red warning light (2a, Fig. E) on the battery charger
control panel stays on, the battery charger is charging
the batteries.
3.
When the green warning light (2c, Fig. E) turns on, the
battery charging is completed.
4.
Once the battery charging is completed, disconnect the
battery charger cable (31, Fig. C) from the electrical
mains and wind it round its support (32).
5.
Carefully lower the tank assembly (4, Fig. J) with the
handlebar (2, Fig. C).
6.
Turn the handwheel (3, Fig. J) clockwise until the tank
assembly is locked.
7.
When the tank (4, Fig. G) has been filled, the machine is
ready to be used (see the related paragraph for the
procedure).
NOTE
For further information about the battery
charger (1, Fig. E) operation, see the related
Manual.
FUSE CHECK/REPLACEMENT
1.
Disconnect the battery connector (30, Fig. C).
2.
Remove the handle (15, Fig. E) from the squeegee
lifting/lowering lever.
3.
Unscrew the nuts (16, Fig. E), carefully remove the cover
(9), and move the panel (11) as necessary.
4.
Check/replace the following fuses:
– Function electronic board fuse (100A) (7, Fig. E);
– Drive electronic board fuse (30A) (8, Fig. E).
5.
Carry out steps from 1 to 3 in the reverse order.
909 5319 000(3)2005-01 A
DISASSEMBLY/ASSEMBLY OF THE
BRUSH-HOLDER/PAD-HOLDER DECK OR
CYLINDRICAL BRUSH-HOLDER DECK
NOTE
On the machines from Serial Number
044515049, it is possible to install either a
brush-holder/pad-holder deck (12, Fig. C) or a
cylindrical brush-holder deck (15), according
to the following instructions.
Disassembly
1.
If there is recovery water in the tank (5, Fig. G) drain it
through the hose (26, Fig. C).
2.
If there is solution in the tank (4, Fig. G) drain it through
the hose (27, Fig. C).
3.
Drive the machine on a level ground.
4.
Turn the ignition key (10, Fig. B) to "0" position.
5.
Disconnect the battery connector (30, Fig. C).
6.
Unscrew the handwheel (3, Fig. J).
7.
By means of the handlebar (2, Fig. C) lift the tank
assembly (4, Fig J) completely to operate on the deck
(12 or 22, Fig. J).
8.
Disconnect the solution hose (21, Fig. J) from the deck.
9.
Disconnect the motor connector (11, Fig. J).
10. Remove the two cotter pins (19, Fig. J).
11. Unscrew the handwheel (20, Fig. J) and remove the
brush-holder/pad-holder deck (12) or the cylindrical
brush-holder deck (22).
12. According to the type of deck, remove the spoiler (14,
Fig. J) or the spoiler (29) by disengaging the retainers.
Assembly
13. Assemble the components in the reverse order of
disassembly, and pay particular attention to the
following:
– when the brush-holder/pad-holder deck (12, Fig. J) is
installed on the machine, the gas spring must be
connected [active position (1, Fig. H)], as show in the
figure;
– when the cylindrical brush-holder deck (22, Fig. J) is
installed on the machine, the gas spring must be
disconnected [idle position (1, Fig. I)] by disengaging
the end (2, Fig. H) from the ball joint (3) and locking
it on the stopper (2, Fig. I).
CAUTION!
When the cylindrical brush-holder deck (22,
Fig. J) is installed on the machine, if the gas
spring is in the active position (1, Fig. H), the
system detects a deck pressure on the ground
overload, and the warning lights (9a, 9b, 9c,
Fig. B) turn on.
USER MANUAL
17
Publicité
Chapitres
Dépannage
