Publicité
Les langues disponibles
Les langues disponibles
USER MANUAL
Cylindrical brush installation
9.
Insert the ignition key (10, Fig. B) and turn it to "I"
position.
10. Turn on the cylindrical brush-holder deck lifting/lowering
switch (2, Fig. B).
WARNING!
Before turning on the cylindrical brush-holder
deck lifting/lowering switch (2, Fig. B), always
check that, between the deck (15) and the
above tank assembly, there is no foreign
material which may prevent the deck from
lifting.
11. Turn the ignition key (10, Fig. B) to "0" position and
remove it.
12. Unscrew the handwheels (25, Fig. J) and remove the
lids (24) by pushing them downwards and pressing on
the handwheels.
13. Install the cylindrical brushes (23).
The cylindrical brushes can be installed on either sides.
14. Reinstall the lids (24, Fig. J) and fix them with the
handwheels (25).
Squeegee installation
15. Install the squeegee (16, Fig. C) and fix it by means of
the handwheels (17), then connect the hose (24) to the
squeegee.
16. Using the handwheel (18, Fig. C), adjust the squeegee
so that its rear blade (20) - in all its length - touches the
floor and that the front blade (19) is slightly detached
from the floor.
Solution tank filling
17. Open the tank cover (1, Fig. G).
18. Lift the shield (15, Fig. G) and, by means of the
extractible hose (6), fill the solution tank (4) with the
appropriate solution for the cleaning to be carried out.
Do not fill the solution tank completely, leave a few
centimetres from the edge.
Always follow the dilution instructions on the label of the
chemical product used to create the solution.
The solution temperature must not exceed 40°C.
Using the transparent hose (1, Fig. J) and the marks (2),
it is possible to check the quantity of solution in the tank.
Moreover, it is possible to consult a gallon/litre table
located on the inner side of the cover (1, Fig. G).
CAUTION!
Use only low-foam and non-flammable
solutions, intended for automatic scrubber
applications.
Adjustments
19. Using the knobs (3, Fig. C), adjust the handlebar (2) to
reach a comfortable position.
10
MACHINE START AND STOP
Start
1.
Prepare the machine as described in the previous
paragraph.
2.
Lower the squeegee (16, Fig. C) by means of the lever
(25).
When the lever (25) is lowered, the vacuum system
starts operating. When the lever (25) is lifted, the
vacuum system stops after a few seconds.
3.
Position the solution flow control lever (4, Fig. B) in the
most appropriate position, depending on the type of
cleaning to be carried out:
– ECO system: when the lever (4) is in the "ECO"
position (5), the machine works in a special condition
of programmed water "economy" usage; as the water
flow is set and constant, the machine can work with
a washing autonomy of 66 minutes (1.2 litres/min
average).
– Variable system: if the lever is in the upper area,
related to the variable flow, it is possible to have a
capacity ranging from 3.8 litres/min minimum to 9.4
litres/min maximum.
In no case it is possible to close completely the water
flow to the brushes during operation.
4.
Insert the ignition key (10, Fig. B) and turn it to "I"
position.
NOTE
If the green warning light (9a, Fig. B) turns on,
the machine is ready to be used. If the yellow or
red warning light (9b or 9c) turns on, it is
necessary to charge the batteries (see the
procedure in Maintenance chapter).
5.
Lower the brush/pad/cylindrical brush-holder deck
(11/14, Fig. C) by means of the switch (2, Fig. B).
NOTE
While the deck (12/15, Fig. C) is moving from
the lifted position to the lowered position, the
warning light on the switch (2, Fig. B) flashes;
when the deck has reached the lowered
position, the warning light stays on.
6.
If equipped, disengage the parking brake by pulling the
levers (34 and 37, Fig. C) at the same time, and then
release them.
7.
With a hand on the handlebar (2, Fig. C), operate the
machine by pressing the paddle (4, Fig. C): the machine
will start moving and the brushes/pad-holder will start
rotating.
8.
Operate on the speed adjuster (7, Fig. B) to change the
machine speed.
909 5319 000(3)2005-01 A
Publicité
Chapitres
Dépannage
