Entsorgung - steute RF 95 SW868 Instructions De Montage Et De Câblage

RF 95 SW868/SW915/SW917/EN868
//
Montage- und Anschlussanleitung / Funk-Befehlsgeräte
Mounting and wiring instructions / Wireless command devices
Instructions de montage et de câblage / Organes de commande sans fil
Istruzioni di montaggio e collegamento / Dispositivi di comando wireless
Instruções de montagem e instalação / Dispositivos de comando sem fio
Инструкция по монтажу и подключению / Радиокомандоаппараты
Deutsch (Originalbetriebsanleitung)

Entsorgung

- Nationale, lokale und gesetzliche Bestimmungen zur Entsorgung
beachten.
- Materialien getrennt dem Recycling zuführen. Eventuell enthaltene
Batterien fachgerecht entsorgen.
English
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer.
In case of doubt, the German language version of these instructions
shall prevail.
Scope of delivery
1 device, 2 mounting nuts, 1 mounting and wiring instructions, carton.
Intended use
The device of type SW868 is intended for use in the European Union.
It complies with the European Union's Directive 2014/53/EU (RED) for
radio equipment.
The device of type SW915 is intended for use in Canada, USA, and Mex-
ico. It complies with the requirements of FCC Rules and IC Rules, RSS-
210. It has an approval number for the Mexican states.
The device of type SW917 is intended for use in Brazil. It complies with
the requirements of Resolucão 242/2000.
The one-channel wireless switch is used to switch electrical loads via
radio transmission. The transmission is carried out at a frequency
of 868.3 MHz (EU) or 915.0 MHz (USA, Canada, Mexico) or 917.0 MHz
(Brazil). The receiver must conform to the steute Wireless protocol of
the steute modules. The steute wireless command devices allow for
the realisation of wireless transmission of a push button signal without
batteries on basis of the steute sWave ® wireless technology. The re-
quired energy is generated by an electrodynamic energy generator.
Mounting and wiring
Mount the device on an even surface. The device must be installed ac-
cording to the mounting and wiring instructions of the receiver. The
wireless range accordingly depends on the local conditions. Thus,
the radio signal can be strongly affected by conductive materials.
This also includes thin foils, e.g. aluminium laminations on insula-
tion materials.
Design of wireless range
Because radio signals are electromagnetic waves, the signal is atten-
uated on its way from the transmitter to the receiver. This means the
electrical as well as the magnetic field strengths decrease inversely
proportionally to the squared distance of transmitter and receiver
(E,H~1/r²). In addition to this natural restriction of the wireless range,
further interference factors occur: Metal parts, e.g. armours in walls,
metal foils of thermal insulations or vapour-deposited metal layer
heat protection glass reflect electromagnetic waves. Therefore, a so-
called deadspot can be found behind them. Radio waves are able to
penetrate walls, but the attenuation increases even more than in the
free field.
Penetration of radio waves:
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical wireless ranges are:
Line of sight in free field (LR):
Line of sight in free field (ULR):
Line of sight indoors (LR):
Line of sight indoors (ULR):
Safety
The electrical connection may only be carried out by authorised per-
sonnel. Do not use the device in connection with other devices whose
direct or indirect purpose is to ensure life or health, or whose opera-
tion may pose a threat to humans, animals or material assets.
N.B.
The processing of one switching command from transmitter to re-
ceiver lasts approx. 80 to 100 ms on basis of the sWave® data trans-
mission. The switching signal of a transmitter must not be generated
in shorter time sequences otherwise this signal will be suppressed.
Subject to technical modifications. Reconstruction and alterations at
the device are not allowed. steute does not assume any liability for
recommendations made or implied by this description. New claims for
guarantee, warranty or liability cannot be hereby derived beyond the
general terms and conditions of delivery.
Maintenance
With rough conditions, we recommend routine maintenance as follows:
1. Removal of all dirt particles.
Cleaning
- In case of damp cleaning: use water or mild, non-scratching,
non-chafing cleaners.
- Do not use aggressive cleaners or solvents.
Clean enclosure on the outside only. Clean enclosure with household
cleaning agents. Do not use compressed air to clean.
2 / 20
90...100%
65...95%
10...90%
0...10%
approx. 450 m
approx. 700 m
approx. 40 m
approx. 50 m