Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TFA_No_30.3033_Anleit_8_sprach
MIAMI
– Wireless pool thermometer
•
Hold "ALERT" button for 3 seconds to enter the Alert setting mode. Indoor temperatu-
re flashes. Press " " or " " button to select indoor or outdoor temperature and the
requested channel for the temperature alert. Press "ALERT" button to confirm the set-
tings. Press " " or " " button to set the upper temperature limit (upwards arrow
is flashing). Press "ALERT" button to confirm the settings. Press " " or " " button to
set the lower temperature limit (downwards arrow
•
When passing or falling below the selected temperature limit an alarm signal will
sound for 5 seconds and the temperature display begins to flash. The alarm signal
keeps on beeping every minute as long as the temperature is higher/lower than the
preset value (5 times maximum) or the ALERT button is pressed.
•
Attention: Is the temperature within the preset limits the display stops flashing.
5. Outdoor thermo sensor
•
After starting up the sensor will automatically transmit the temperature values to the
display unit.
•
Press "°C/°F" button on the thermo sensor unit to change the temperature unit on the
sensor display from °C to °F.
•
Press "TX" button on the thermo sensor unit to transmit temperature to the weather
station manually (e.g. for testing or in case of loss of transmitter signal). The display
unit gives a "beep" sound if it received the temperature.
5.1 Zusätzliche Außensender
•
The unit is expandable up to 3 outdoor transmitters (item no. 30.3133 / 30.3139),
also for the control of outdoor temperature and remote rooms, e.g. children's room,
wine-cellar
•
For having more than one external transmitter, select different channels for each sen-
sor by the "CHANNEL" switch. The new transmitter will be received automatically by
the display unit. The pool sensor is firmly adjusted to channel 1.
•
The temperature measured by the sensor is shown on the display of the display unit. If
you have installed more than one transmitter, press "CHANNEL" button to change bet-
ween the outdoor transmitters.
•
You can also choose an alternating channel display. Press CHANNEL button. After the
last registered channel a circle symbol appears (Display
nel 2 or
for channel 3 and
•
To cancel an unused channel hold "CHANNEL" button for 3 seconds. If a new channel
is received it will be automatically registered again.
6. Positioning of display unit and transmitter
•
The pool sensor floats on the water surface and measures the temperature in a water
depth of about 100 mm. You can fix the pool sensor by a fastening rope.
12
04.06.2008
10:05 Uhr
Seite 7
is flashing).
for channel 1,
for alternating channel).
MIAMI
– Wireless pool thermometer
•
Place the display unit at the final position. Avoid the vicinity of any interfering field
like computer monitors or TV sets and solid metal objects.
•
Check the transmission of the signal from the transmitter to the display unit (transmis-
sion range 30 m free field, within ferro-concrete rooms, especially with metal parts,
the received signal is naturally weakened.
•
If necessary chose another position for transmitter and/or display unit.
7. Battery Replacement
•
When the batteries in the pool sensor (channel 1) are used up, low battery icon appe-
ars on the display of the main unit.
•
Open the battery compartment of the transmitter (screwed).
•
Use alkaline batteries only. Observe correct polarity. Low batteries should be changed
soon to avoid the damage resulting from a leaking battery.
•
After successful installation screw up the battery compartment of transmitter carefully.
Attention: Please do not dispose of old electronic devices and used batteries in house-
hold waste. To protect the environment, take them to your retail store or to nearest
civic amenity site to be disposed of according to national or local regulations.
8. Notes
•
Always read the users manual carefully before operating the unit.
•
Please switch off the pool sensor (pressing "TX" button and "°C/°F" button at the
same time) if not using it for a long time.
•
Use a pin to press the "RESET" button if the unit does not work properly.
•
Avoid placing the clock near interference sources/metal frames such as computer or TV sets.
•
Do not expose the instrument to extreme temperatures, vibration or shock.
9. Liability Disclaimer
•
The product is not a toy. Keep it out of reach of children.
•
The product is not to be used for medical purpose or for public information, but is
determined for home use only.
•
Improper use or unauthorized opening of housing will mean the loss of warranty.
•
No part of this manual may be reproduced without written consent of TFA Dostmann.
for chan-
10. Specifications
Measuring range:
Indoor temperature:
Water temperatur:
Batteries:
0°C...+50°C (32...+122°F)
-20...+50°C (-4...+122°F)
3 x 1,5 V AA for main unit and
2 x 1,5 V AA for transmitter (included)
13
Publicité
Table des Matières
