Mitsubishi Electric CITY MULTI PKFY-NBMU-E2 Manuel D'utilisation page 9

Masquer les pouces Voir aussi pour CITY MULTI PKFY-NBMU-E2:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

6. Timer
<Setting the Weekly Timer>
5. Press the appropriate Set Time button
sired time (at
).
tervals, then in ten-minute intervals, and then in one-hour intervals.
6. Press the ON/OFF button
OFF) at
.
* Each press changes the next setting, in the following sequence: No
display (no setting)
"ON"
7. Press the appropriate Temperature set button
temperature (at
).
* Each press changes the setting, in the following sequence: No dis-
play (no setting)
75
No display.
(Available range: The range for the setting is 12°C, 54°F to 30°C,
86°F. The actual range over which the temperature can be control-
led, however, will vary according to the type of the connected unit.)
8. After making the appropriate settings at Steps 5, 6 and 7, press the
Filter
button
to lock in the values.
To clear the currently set values for the selected operation, press and
quickly release the Check (Clear) button
* The displayed time setting will change to "—:—", and the On/Off
and temperature settings will all disappear.
(To clear all weekly timer settings at once, hold down the Check
(Clear) button
for two seconds or more. The display will begin
blinking, indicating that all settings have been cleared.)
Note:
Your new entries will be cancelled if you press the Operation mode
before pressing the Filter
If you have set two or more different operations for exactly the
same time, only the operation with the highest Operation No. will be
carried out.
as you wish.
10. Press the Operation mode (Back) button
control screen and complete the setting procedure.
11. To activate the timer, press the Timer On/Off button
"Timer Off" indication disappears from the screen. Be sure that the
"Timer Off" indication is no longer displayed.
* If there are no timer settings, the "Timer Off" indication will blink on
the screen.
<How to View the Weekly Timer Settings>
SUN
TIMER
1. Be sure that the weekly timer indicator is visible on the screen (at
2. Press the Timer Menu button
screen (at
).
3. Press the Timer On/Off (Set Day) button
day you wish to view.
4. Press the
or
Operation button (
the timer operation shown on the display (at
* Each press will advance to the next timer operation, in order of time
setting.
5. To close the monitor and return to the standard control screen, press
the Operation mode (Back) button
<To Turn Off the Weekly Timer>
Press the Timer On/Off button
F
<To Turn On the Weekly Timer>
Press the Timer On/Off button
goes dark.
F
as necessary to set the de-
to select the desired operation (ON or
"OFF"
to set the desired
77
...
84
87
53
once.
button
.
to return to the standard
, so that the
Timer Settings
ON
OFF
F
WEEKLY
so that "Monitor" is indicated on the
as necessary to select the
or
) as necessary to change
).
.
so that "Timer Off" appears at
TIME SUN
F
WEEKLY
so that the "Timer Off" indication (at
TIME SUN
F
WEEKLY
6.1.2. Simple Timer
You can set the simple timer in any of 3 ways.
• Start time only:
-
The air conditioner starts when the set time has elapsed.
• Stop time only:
The air conditioner stops when the set time has elapsed.
• Start & stop times:
The air conditioner starts and stops at the respective elapsed times.
The simple timer (start and stop) can be set only once within a
72-hour period.
The time setting is made in hour increments.
Note:
*1. Weekly Timer/Simple Timer/Auto Off Timer cannot be used at
...
73
the same time.
*2. The simple timer will not operate when any of the following con-
ditions is in effect.
The timer is off; the system is in malfunction state; a test run is
in progress; the remote controller is undergoing self-check or
remote controller check; the user is in the process of selecting
a function; the user is in the process of setting the timer; the
BACK
PAR-21MAA
<How to Set the Simple Timer>
1. Be sure that you are at a standard control screen, and that the simple
timer indicator is visible in the display (at
When something other than the Simple Timer is displayed, set it to
).
SIMPLE TIMER using the function selection of remote controller (see
8.[4]–3 (3)) timer function setting.
2. Press the Timer Menu button
screen (at
). (Note that each press of the button toggles the display
between "Set Up" and "Monitor".)
3. Press the ON/OFF button
timer setting. Press the button once to display the time remaining to
ON, and then again to display the time remaining to OFF. (The ON/
OFF indication appears at
• "ON" timer:
hours has elapsed.
• "OFF" timer:
.
hours has elapsed.
4. With "ON" or "OFF" showing at
button
as necessary to set the hours to ON (if "ON" is displayed) or
the hours to OFF (if "OFF" is displayed) at
• Available Range: 1 to 72 hours
5. To set both the ON and OFF times, repeat Steps 3 and 4.
)
* Note that ON and OFF times cannot be set to the same value.
6. To clear the current ON or OFF setting: Display the ON or OFF setting
(see step 3) and then press the Check (Clear) button
time setting clears to "—" at
or only an OFF setting, be sure that the setting you do not wish to use
is shown as "—".)
Hr
ON
AFTER
SIMPLE
TEMP.
ON/OFF
MENU
ON/OFF
FILTER
MONITOR/SET
DAY
CHECK
TEST
CLOCK
OPERATION
CLEAR
Timer Setting
Action (On or Off)
Hr
ON
AFTER
* "— —" is displayed if there is no
setting.
SIMPLE
).
, so that the "Set Up" appears on the
to display the current ON or OFF simple
).
: Press the appropriate Set Time
.
. (If you want to use only an ON setting
so that the
9

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

City multi pkfy-nhmu-e2City multi pmfy-nbmu-e

Table des Matières