General Maintenance; Maintenance - Hoover ONEPWR BH53000 Guide D'utilisateur

WARNING!
To avoid serious personal injury, always remove the
battery pack from the product when cleaning or
performing any maintenance.

General Maintenance

Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths to
remove dirt, dust, oil, grease, etc.
This product contains no serviceable parts.
If appliance is not working as it should, has been dropped,
damaged, left outdoors or dropped in water, contact customer
service at 1.800.406.2005.
WARNING!
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact with
plastic parts. Chemicals can damage, weaken or destroy
plastic which could result in serious personal injury.
Emptying the Dirt Cup
See Figure 7, page 8
• Remove the battery pack.
• Push down the latch on the dirt cup to release. Tilt and lift to
remove the dirt cup from the stick vac.
• Hold the dirt cup over a trash bin and press the dirt cup re-
lease button to empty.
• To close, push the door until it locks back into place.
• Replace the dirt cup by rocking it back into place.
Cleaning the Filter and Cyclone
See Figure 8, page 9
• Pull open the lid of the dirt cup to access the filter.
• To clean the cyclone, lift to remove. Clean dirt and debris by
wiping the metal screen with a cloth and then place back
into the dirt cup.
• Pull the filter away and tap over a trash can to remove dirt.
Rinse filter under warm water until water is clear. Allow filter
to dry for 24 hours before reinserting.
WARNING!
Do not use vacuum without the filter or cyclone in place.
WARNING!
Do not use soap or other chemicals to clean. Dry filter
completely, for up to 24 hours, before reinstalling into
the product.
PG.5

MAINTENANCE

Removing and Replacing the Brush Roll
See Figure 9, page 9
Risk of personal Injury, brushroll may suddenly restart.
Turn power switch OFF and remove battery before cleaning
or servicing.
• Remove powered nozzle from reach wand. Using a coin,
push and turn the brush roll lock counterclockwise to re-
lease the brush roll.
• Pull the brush roll out of the powered nozzle
• To remove any threads or hair, slide the blade of a pair of
scissors into the groove of the brush roll and cut along the
groove. Clear any dirt/debris from the end caps and inside
the housing of the powered nozzle.
• Re-fit the brush roll into the housing and turn the brush roll
lock clockwise to lock.
Microfiber Hard Floor Nozzle
See Figure 10, page 10
• Remove the powered nozzle from the reach wand. Using a
coin, push and turn brush roll lock counterclockwise to re-
lease the brush roll.
• Gently use your fingers to lift the brush roll from the nozzle
cavity on the side closest to the brush roll lock.
• To remove any debris from the brush roll gently wipe with a
dry cloth. Clear any dirt/debris from the end caps and inside
the housing of the powered nozzle.
• Re-fit the brush roll into the housing and turn the brush roll
lock clockwise to lock.
For troubleshooting, please visit Hoover.com
Thermal Protector
A thermal protector has been designed into your cleaner to
protect it from overheating. When the thermal protector acti-
vates, the cleaner will stop running. If this happens, proceed
as follows:
1. Turn cleaner OFF and remove battery pack
2. Empty dirt cup
3. Inspect the filter and cyclone for any obstructions. Clear
obstructions if present
4. After the battery pack is removed and the motor cools for
30 minutes, reinstall the battery pack. The thermal pr tector
will deactivate and cleaning may continue.
If thermal protector continues to activate after following the
above steps, call Customer Service at 1-800-406-2005.
WARNING!