Preparing For Use - MSW TWIST-A-SAW Manuel D'utilisation

2
1
3
4 5
12
7
6
11
10
8
9
1. rotational speed control
2. hook
3. ON/OFF switch
4. knob fixing the side handle
5. secure handle
6. cutting depth limiter knob
7. suction pipe
8. cutting depth limiter
9. cutting width limiter
10. cutting width limiter knob
11. fixing the tool
12. spindle protection
Circular guide:
1
2
9
4
3
8
7 6 5
1. rotational speed control
2. ON/OFF switch
3. knob for setting the diameter
4. holder of the guide for cutting out circles
5. scale
6. bit for cutting the wheel
7. setting disc
8. bit for cutting
9. bit locking screw
Rotational tip:
1 2
3
5 4
1. tip
2. flexible shaft
3. holder
4. lock
5. clamping grip
Elements required during work:
Tool: Description:
Multifunc- The use of the holder guarantees
tion holder reliable and stable holding of the
with cutting device. It is necessary to hold the
width holder with one hand and the rotating
tool with the other hand.
12
Tool: Description:
Multifunc- The cutting depth limiter is used to
tion holder set the height of the cutting tips. The
with cutting cutting width limiter is used to cut
width straight lines in relation to the edges.
Circular The circular guide is used for precise
guide cutting-out of circles (circumferences).
Tip for dust The tip for dust sucking-off enables
sucking-off to connect a vacuum cleaner with the
device.
Rotational The rotational tip is a long and flexible
tip roller that leads to the head of the
rotating tool. The blades are installed
on the head which can be held in your
hands, which gives you more control
when working. The rotational tip must
be used with small tips only.
Replacement of the clamps (of the sleeve):
1 3
1. spindle
2
2. ring
3. nut
1. Remove the blades from the device.
2. Turn the nut counter-clockwise and remove it from
the spindle.
3. Remove the ring from the spindle and install a new
one. The ring can be installed from any side.
4. Install the nut and screw it on.
WARNING! Screwing the nut without the cutting tip
causes reduction in the diameter of the ring what
making it difficult to install a blade.
When storing the device, the ring must be stored
without the cutting tip installed.
Installation of cutting tips:
1
3
1. lock button
2. nut
2
3. spanner
4
4. cutting tip
1. Remove the plastic cover from the tip (if installed).
2. Press the lock button, then turn the nut until the
button will be blocked.
3. Loosen the nut. To this aim it is necessary to press
the lock button and using a flat spanner (Ø16mm) to
turn the nut counter clockwise.
4. If the cutting tip is installed, it is necessary to remove
it.
5. Insert the cutting tip into the ring and then slide
it out to a length of 1 - 3mm, the gap created will
protect the tip against overheating.
Rev. 22.02.2018
WARNING! If the diameter of the installed tip is
different from the previous one it is necessary to
change and install an appropriate ring as well.
6. Make sure that the grooves on the blade are visible.
Squeezing the ring on them may cause breaking of
the tip.
7. After installing the tip in the ring it is necessary to
press the lock button and tighten the nut as firmly as
possible in clockwise direction.
8. Use a ɸ16mm spanner to tighten the nut.
Mounting the multifunctional holder:
4
3
2
1. ring of the holder
2. ring knob
5
3. button
1
4. the bottom of the device
5. key
1. Loosen the ring knob.
2. Install the holder ring to the bottom of the device.
3. Align the button with the key.
4. When the button with key is on one level it is
necessary to put the ring to the end. WARNING! The
holder ring must be pressed as deep as possible.
5. Fasten the holder ring by clamping the knob.
6. In order to remove the holder it is necessary to
proceed in reverse order.
WARNING! Do not use the device without the multi-
function holder!
Setting the secure holder:
1
2
1. fastening knob
2. safe holder
The safe holder can be adjusted where it is needed.
The manner of placing the safe holder:
• horizontally when the device is used as a saw
• vertically or at an angle if the device is used as
a jigsaw
• upside down, depending of the work performed
The method of mounting of the safe holder:
1. Loosen the fastening knob.
2. Set the safe holder in the selected position.
3. Turn the fastening knob

4.2 Preparing for use

Setting the cutting depth:
Rev. 22.02.2018
1
1. knob of the cutting depth limiter
2
2. foot of the cutting depth limiter
1. Loosen the foot of the cutting depth limiter and then
set the desired height by moving the foot of the
cutting depth limiter down or up.
2. Then tighten the foot of the cutting depth limiter.
3. Check the tip depth and make sure that the ring with
the tip is safely fastened.
WARNING! The cutting tip should exceed the
material cutting depth by 4 mm! Example: In order to
cut a material with a width of 10mm, the cutting tip
should protrude 14 mm beyond the bottom of the
foot of the cutting depth limiter (4mm beyond the
material)!
Installation of the circular guide:
2
3
1
4
8
5
6
7
1. protection
2. internal disk
3. base of the multifunctional holder
4. knob
5. pin
6. hub
7. external disk
8. hole of the jig saw guide
1. Install the multifunction holder.
2. Set the cutting depth limiter.
3. Unscrew the internal disk from the external disk.
4. Place the internal disk in the holder base. Make
sure that the teeth of the inner disk are properly
placed in the teeth of the holder base.
5. Place the hole of the jigsaw guide on the tread of
the internal disk. Make sure that the pin will be
pointing down.
6. Install the external disk on the internal disk and
tighten it (do not overtighten). Make sure that the
hub has been correctly seated in the hole.
7. Loosen the knob, set the radius of the circle and
tighten the knob.
8. Install the appropriate blade and tighten.
Installation of the cutting width limiter:
1
2
13