Triton AJA 300 Instructions D'utilisation Et Consignes De Sécurité page 5

e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
ASSEMBLY
Step 1
Fit the Plate Clamp Bases (4) to the underside corners
of the Jigsaw Plate (1) with the M6 x 45 Countersunk
Screws (5) and M6 Flange Nuts (6), as shown. Do not
completely tighten.
Fit the jigsaw plate into the router table cut-out
(clamp bases facing down) with the slots at the front
(switchbox end). Push the clamp bases outward until
they locate against the square tube supports while
tightening with a Phillips screwdriver.
Screw the Plate Clamp Knobs (7) onto the screws until
they hold the plate firmly into the table (they cut their
own thread).
In use: The clamps have flat side edges. When all
four cut-aways are facing outward the plate can be
removed. Turn the knobs clockwise approximately half
a turn to tighten it back down.
Step 2
For this step, release the plate clamp knobs and turn
the plate upside down in the router table cut-out, with
the clamps upward.
Use a square to ensure the jigsaw blade is set at 90° to
its base, and make any necessary adjustments.
Place your jigsaw onto the plate with the blade locating
approximately central through the jigsaw blade slot.
Position the jigsaw base approximately parallel to the
sides of the plate.
Fit the Back Stop (8) to the rear slot using the M6 x
20mm Coach Bolt (9) and a flange nut. Tighten into
position against the back edge of the jigsaw base.
Position the four Clamp Bases (10) into the slots on
either side of the jigsaw base with their straight edges
touching the sides of the base. Tighten them into
position with the M6 x 40mm Coach Bolts (11) and M6
flange nuts.
Screw the Clamp Knobs (12) on (they cut their own
thread) until they tighten firmly onto the top edge of
the jigsaw base. The flat sides of the clamps should be
facing away from the jigsaw. Note: It may be necessary
to remove the jigsaw while screwing the clamp knobs
into position.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
In use: When the flat sides of all four clamps are facing
inward the jigsaw can be removed. Turn the knobs
clockwise half a turn to tighten it back down.
Remove the plate then re-fit and lock it into the Router
Table with the blade pointing upward.
Step 3
Push the Blade Guard (13) into the front of the
Overhead Arm (2) and fit the M6 x 40mm Coach Bolt
(14) and Overhead Arm Fixing Knob with M6 nut (15).
As the bolt is designed for a firm fit pulling the guard
forward slightly will allow easier assembly.
Step 4
Insert the M6 x 40mm Coach Bolt (14) from inside the
edge of the Router Table. Fit the Support Arm (3) into
the square hole and onto the coach bolt and slide it in
completely. Tighten into position with a Support Arm
Fixing Knob with M6 nut (21).
Slide the overhead arm onto the round tube of the
support arm.
Raise the arm and fit the Bridge (16) using the Hex Bolt
(17) and the other Support Arm Fixing Knob (21), as
shown.
Lower the the arm onto the jigsaw blade and position
the arm until the blade is central within the guard.
Tighten the arm in place. Storage note: Loosen the
arm clamp when storing for extended periods to avoid
fatigue.
Step 5
Insert the Arm Locator (18) into the slot on the support
arm round tube, with the side wall of the overhead
arm engaging in the groove on the locator. Tighten the
locator firmly in position using the M6 x 10mm Screw
(19) and Flange Nut (6).
Push-fit the Tube Plug (20) into the end of the tube.
Note the notch in the plug must line up with the arm
locator.
General Safety Instructions / Assembly
GB
5