Behringer PMP1000 Mode D'emploi page 10

EUROPOWER PMP1000/4000/6000 • pg 18
FBQ FEEDBACK DETECTION
If feedback occurs, press the EQ IN and FBQ FEEDBACK DETECTION
buttons. Press the MAIN MIX/MONITOR button to assign the graphic
EQ to the mains or monitor speakers.
Si se produce realimentación, pulse los botones EQ IN y FBQ
FEEDBACK DETECTION. Pulse el botón MAIN MIX/MONITOR para
asignar el ecualizador gráfico a la corriente eléctrica o a los
altavoces de monitoreo.
En cas de larsen, appuyez sur les touches EQ IN et FBQ FEEDBACK
DETECTION. Appuyez sur la touche MAIN MIX/MONITOR pour affecter
l' é galiseur graphique aux enceintes de façade ou aux retours.
An LED will light on the EQ slider that corresponds with the
feedback frequency.
Se encenderá un LED en el control del ecualizador que
corresponde a la frecuencia de realimentación.
Une LED s'allume sur le curseur EQ correspondant à la
fréquence de Larsen.
Lower the lit EQ slider until feedback stops.
Deslice hacia abajo el control de dicho ecualizador hasta que
se detenga la realimentación.
Réduisez le curseur EQ allumé jusqu'à ce que le Larsen cesse.
www.behringer.com
EUROPOWER PMP1000/4000/6000 • pg 19
Specifications
MICROPHONE INPUTS PMP1000 PMP4000 PMP6000
Type
XLR, electronically balanced input circuit
Mic E.I.N. (20 Hz - 20 kHz)
@ 0 Ohm source resistance -134 dB / 136 dB A-weighted
@ 50 Ohm source
-131.5 dB / 134 dB A-weighted
resistance
@ 150 Ohm source
-129 dB / 155 dB A-weighted
resistance
< 10 Hz - 200 kHz (-1 dB)
Frequency response
< 10 Hz - > 200 kHz (-3 dB)
Gain
+10 dB, +60 dB
Max. input level
+12 dBu @ +10 dB gain
approx. 2.6 kOhm balanced /
Impedance
1.3 kOhm unbalanced
109 dB / 112 dB A-weighted
Signal-to-noise ratio
(0 dBu In @ +10 dB gain)
Noise (THD + N)
0.002% / 0.0018% A-weighted
MONO LINE INPUTS
Type ¼" TS connectors, balanced
Impedance approx. 20 kOhm
Max. input level
+21 dBu
STEREO LINE INPUTS
Type – ¼" TRS connectors, unbalanced
Impedance – > 3.6 kOhm
Max. input level
– +22 dBu
EQUALIZER
Low
80 Hz / +/-15 dB
100 Hz - 8 kHz /
Mid
2.5 kHz / +/-15 dB
+/-15 dB
High 12 kHz / +/-15 dB
2 TRACK INPUT
Type RCA
Impedance
approx. 3.6 kOhm
PREAMP OUTPUTS
MAIN
Type ¼" TRS connectors, unbalanced
Impedance
approx. 150 Ohm, unbalanced
Max. output level
+21 dBu
MONITOR
Type ¼" TRS connectors, unbalanced
Impedance approx. 150 Ohm, unbalanced
Max. output level
+21 dBu
STEREO OUTPUTS
Type – ¼" TRS connectors, unbalanced
Impedance – approx. 150 Ohm, unbalanced
Max. input level – +21 dBu
Type
RCA RCA
Impedance
approx. 1 kOhm approx. 1 kOhm
Max. input level +21 dBu +21 dBu
www.behringer.com
PMP1000/4000/6000
LOUDSPEAKER OUTPUTS PMP1000 PMP4000 PMP6000
Type
Professional locking connector
Load impedance:
MAIN L/R 4 - 8 Ohm
MONITOR/MAIN MONO 4 - 8 Ohm
MAIN MONO/MAIN MONO
4 - 8 Ohm
BRIDGE
8 - 16 Ohm
DSP
Converter 24-bit Delta-Sigma, 64/128-times oversampling
Dynamics D/A 90 dB
Sampling rate
46.875 kHz
Delay Time
max. 5 secs
Signal run time
approx. 1.5 ms
(Line In > Line Out)
DISPLAY
2 x 2-digit,
Type 2-digit, 7 segment LED
7-segment LED
OUTPUT POWER
RMS @ 1% THD, both channels driven:
8 Ohm per channel
90 W 300W
4 Ohm per channel
130 W 600 W
RMS @ 1% THD, bridged mode:
8 Ohm 200 W 1200 W
Peak Power, both channels driven:
8 Ohm per channel
135 W 400 W
4 Ohm per channel
250 W 800 W
Peak Power, bridged mode:
8 Ohm 500 W 1,600 W
POWER SUPPLY
Mains voltage
USA/Canada
120 V~, 60 Hz
China/Korea 220 V~, 50/60 Hz
Europe/Australia 230 V~, 50 Hz
Japan
100 V~, 50 - 60 Hz
Fuse 100 - 120 V~
T 5 A H 250 V T 10 A H 250 V
Fuse 220 - 240 V~ T 5 A H 250 V T 6.3 A H 250 V
POWER CONSUMPTION
Power consumption 500 W 1,050 W
Mains connector
IEC standard receptacle
DIMENSIONS/WEIGHT
4 7/8" x 15 3/8" x 4 7/8" x 18 3/4" x 4 7/8" x 23 1/2" x
16 3/4" 18 1/8" 19 1/2"
Dimensions (H x W x D) 122 mm x 122 mm x 122 mm x
390 mm x 476 mm x 596 mm x
425 mm 460 mm 496 mm
Weight
8 kg/ 17.6 lbs. 10.4 kg/ 22.9 lbs. 13.1 kg/ 28.9 lbs.
EN
ES
FR