Taking Weight Measurement Only (No Bluetooth Output)
Select Weight-Only Key
Press the Weight-only key. After 2 or 3 seconds, "0.0" will appear in the display and the
unit will beep. When "0.0" appears in the display, step onto the platform. The body
weight value will appear. If you remain on the platform, the display will flash for about 30
seconds, and then the power will automatically turn off. If you step off the platform, the
weight will continue to show for about 5 seconds, the "0.0" will appear and the unit will
shut off automatically.
Troubleshooting
If the following problems occur ...then...
• A wrong weight format appears followed by kg, lb, or st-lb.
Refer to Switching the Weight Mode on p.3.
• The display shows
and goes off when the personal key pressed.
No data (age gender, height and activity level) has been stored in the memory.
•
appears on the display, or all the data appears and immediately disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will affect the
accuracy of your measurements. Change all the batteries at the same time with new AA-size batteries.
Note : Your settings will not be erased from the memory when you remove the batteries.
•
appears while measuring.
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
The Body Fat Percentage is more than 75%, readings cannot be obtained from the unit.
• The Body Fat Percentage reading does not appear or
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides on the
measuring platform.
•
appears while measuring.
Reading cannot be obtained if the weight capacity is exceeded
• No reading is obtained after pressing a feature key.
Step off scale when body fat reading appears, then press feature key.
10
appears after the weight is measured.
Output Data Format
Specification
Signal Speed
9600 bps
Start Bit
1 bit
Data Bit Length
8 bits
Parity
None
Stop bit
1 bit
Bluetooth Security Code
PIN
0000
Output Data
Header
Output data (ASCII code)
Control Data
{0
XX
Control Data
˜0
X
Control Data
˜1
X
Control Data
˜2
X
Model No.
MO
"BC-590BT"
Personal No.
PN
X (1 ~ 4:Personal 0:Guest)
Body Type
BT
X (0:Standerd 2:Athlete)
Gender
GE
X (1:Male 2:Female)
Age
AG
XX
Height
cm
Hm
XXX.X
ft - inch
Hf
X.YY.Y (X:feet Y:inch)
Activity Level
AL
X (1 ~ 3)
kg
Wk
XXX.X
Weigtht
lb
Wp
XXX.X
st - lb
Ws
XX.YY.Y (X:st Y:lb)
Total Body Fat
Fw
XX.X
Total Body Water
ww
XX.X
kg
mW
XXX.X
Muscle
lb
mW
XXX.X
Mass
st - lb
mW
XX.YY.Y (X:st Y:lb)
Physique Rating
PR
X
DCI (cal)
rD
XXXX
Metabolic Age
rA
XX
kg
bW
XXX.X
Bone Mass
lb
bW
XXX.X
st - lb
bW
XX.YY.Y (X:st Y:lb)
Visceral Fat Rating
IF
XX
Checksum
CS
XX
Note : • The data are divided with commas (,) for each data.
(zero)
• The terminator (end of data) is CR (ASCII code 0
Substance
kg
2bytes fixed / fixed to "16"
1byte fixed / fixed to "1"
1byte fixed / fixed to "1"
1byte fixed / fixed to "1"
10bytes fixed
1byte fixed
1byte fixed
1byte fixed
1-2bytes variable length
4-5bytes variable length
6bytes fixed
–
1byte fixed
3-5bytes variable length
3-5bytes variable length
–
6-7bytes variable length
–
3-4bytes variable length
4bytes fixed
3-5bytes variable length
3-5bytes variable length
–
6-7bytes variable length
–
1byte fixed
1-4bytes variable length
2bytes fixed
3-5bytes variable length
3-5bytes variable length
–
6-7bytes variable length
–
1-2bytes variable length
2bytes fixed
(zero)
D), LF (ASCII code 0
A).
Mode
lb
st - lb
–
–
–
–
–
–
–
–
–
–
–
–
–
–
11