Table des Matières
Publicité
MANUAL RELEASE
In the event of a power failure, use the manual release device to
move the gate. Remove the plastic cover over the lock, insert the
key and remove the small safety guard.
BIG18:
Turn the handle clockwise (fig. 19).
BIG30-40:
Using the hex wrench provided, rotate the release
assembly counter-clockwise at least one complete
turn (fig. 20B). To restore normal operation, simply
tighten the release assembly (1 fig. 20A) by screw-
ing it in until it reaches the mechanical stop.
LIMIT SWITCH
The gear motors in the BIG series have been designed to work
with an electromechanical limit switch featuring a single dual-effect
switch.
Cable connections:
1 = common
2 = blue (common)
3 = brown (close L.S. – N.C. contact)
4 = black (open L.S. – N.C. contact)
WARNINGS
The fitter is responsible for ensuring the system can be used cor-
rectly and functionally. He must also provide it with all the safety
devices and/or signals required to ensure it complies with current
law. Make sure that each single device is in perfect working order.
As regards vertical tubular gates, the system must be fitted with a
protective mesh covering the whole surface of the gate.
Put up easy-to-read signs informing people that the gate is pow-
ered.
It is forbidden to use the equipment for other purposes or in other
circumstances than those mentioned.
In particular:
1 do not touch the equipment with wet hands;
2 disconnect the power supply before opening the control box
and/or the gear motor;
3 do not pull the power cable to remove the power plug;
4 do not touch the motor unless you are sure it has cooled down;
5 only move the gate when it is completely visible;
6 do not approach the gate if this is moving: wait until it has
stopped;
7 do not allow children or animals to play near the gate;
8 do not allow children or unauthorised people to use the remote
control or other control devices;
9 carry out routine maintenance;
10 in the event of a fault, disconnect the power supply and only
move the gate if it is possible and safe to do so.
MAINTENANCE
Attention: only the maintenance man, who must be a specialised
technician, is allowed to operate the automatic system during
maintenance. The power supply should therefore be disconnected.
If the power supply must be left on for certain operations, each
control device should be checked or disabled (remote controls,
push button strips, etc.) except for the one used by the mainte-
nance man.
ROUTINE MAINTENANCE
Each of the following operations must be carried out when neces-
sary and always every 6 months.
Gate: check the general condition of the gate.
Automation system:
1 check the safety devices.
2 regularly grease the release device
EXTRAORDINARY MAINTENANCE OR BREAKAGE
If major work on electromechanical parts must be carried out, the
faulty part should be removed and repaired in the workshop by the
manufacturer's or other authorised technicians.
GUARANTEE: GENERAL CONDITIONS
TAU guarantees this product for a period of 24 months from the
date of purchase (as proved by the sales document, receipt or in-
voice).
This guarantee covers the repair or replacement at TAU's expense
(ex-works TAU: packing and transport at the customer's expense)
of parts that TAU recognises as being faulty as regards workman-
ship or materials.
For visits to the customer's facilities, also during the guarantee pe-
riod, a "Call-out fee" will be charged for travelling expenses and
labour costs.
The guarantee does not cover the following cases:
• If the fault was caused by an installation that was not per-
formed according to the instructions provided by the com-
pany inside the product pack.
• If original TAU spare parts were not used to install the prod-
uct.
• If the damage was caused by an Act of God, tampering,
overvoltage, incorrect power supply, improper repairs, in-
correct installation, or other reasons that do not depend on
TAU.
• If a specialised maintenance man does not carry out routine
maintenance operations according to the instructions pro-
vided by the company inside the product pack.
• Wear of components.
The repair or replacement of pieces under guarantee does not ex-
tend the guarantee period.
In case of industrial, professional or similar use, this warranty is
valid for 12 months.
BIG Series
17
Publicité
Table des Matières
