Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
-
Cut evenly over this guide line.
Take care to have a secure and safe standing position
when working with your hedge shears in order to avoid
slipping and injury. Always keep the shearing blades
away from your body.
Optimum safety
The 5 special features two-hand safety switch, quick
blade stop, protective cover, blade safety rail and impact
protector are fitted to provide the hedge trimmer with
optimum safety features.
Attention!
If you find out that safety functions, such as
the 2-switch mechanism or the safety stop, are
not functioning while working with the hedge
shears, immediately cease working and take
the machine to a specialised shop for repairing.
Two-hand safety switch (Fig. 4)
To switch the hedge shears on the bar switch in the
handle (A) and the grip switch of the bow-type handle (B)
must be pushed down. To switch the device off let go of
both switches. The motor already stops if one of the two
switches is released.
Quick blade stop
In order to avoid injuries through cuts, the blade will
stop in max. 0.5 sec. when one of the two switches is
released.
Blade safety rail (Fig. 8)
The cutting blade set back from the blade housing reduc-
es the risk of injuries due to unintentional body contact.
Impact protector (Fig. 1)
The extended guide rail prevents unpleasant shocks
(blade recoil) being transmitted to the operator due to
impact with solid objects (wall, ground etc.).
Gear protection feature
If solid objecst are caught in the cutting blade and jam
the motor, switch off the machine at once, disconnect the
power plug from the power socket, remove the object and
continue with the work.
The equipment is also fitted with an overload cutout,
which protects the gears against mechanical damage in
the event of blade jams.
Storing the trimmer after use
The hedge shears must be stored such that there is
no danger of injuries being caused to persons by the
cutting blades!
Important note: The shearing blades should be cleaned
after each use.(see also Section Maintenance).This will
considerably increase the service life of the device. Please
use a lubricator that is not harmful to the environment , e.
g. our service spray. Then put the shears in their case with
the cutting blades first.
GB | Operating Instructions
Repair service
Repairs to electric power tools should only be carried out
by specialist electrical personnel.
Spare parts
If you need accessories or spare parts, please contact our
Service department.
When working with this tool, do not use any accessory parts
other than those recommended by our company. Otherwise
the operator or others in the vicinity could suffer serious
injuries, or the tool could be damaged.
The following information should be provided when or-
dering spare parts:
• Type of machine
• Item number of the machine
Waste disposal and environmental protection
Dispose of the machine properly after it is worn out. Dis-
connect the mains cable in order to prevent misuse. Do
not dispose of the machine with the household waste. In
the interest of environmental protection, take it to a col-
lection point for electric machines. Your responsible local
authority can provide you with addresses and operating
times. Also take the packaging materials and worn out
accessories to the appropriate collection points.
In accordance with European Directive 2012/19/EC on
waste electrical and electronic equipment and its im-
plementation in national law, waste electric tools must
be collected separately for environmentally-compatible
re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the ac-
cessory parts and auxiliary equipment without electrical
components accompanying the waste equipment.
Warranty
For this electric tool, the company provides the end user
- independently from the retailer's obligations resulting
from the purchasing contract - with the following war-
ranties:
The warranty period is 84 months beginning from the
hand-over of the device which has to be proved by the
original purchasing document. Wearing parts and defects
caused by the use of non fitting accessories, repair with
parts that are not original parts of the manufacturer, use
of force, strokes and breaking as well as mischievous
overloading of the motor are excluded from this warranty.
GB-6
Only for EU countries
Do not discard electric tools in the household
waste!
Publicité
Table des Matières
