Toshiba Carrier MCY-MAP0367HS-UL Manuel Du Propriétaire page 13

Masquer les pouces Voir aussi pour MCY-MAP0367HS-UL:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

6
Push the
button to finish the setting.
0001 - 0005
(Louver position
Louver No.
code)
* F1 appears in the CODE No. section on the
remote control. This indicates that the louver 01
is selected.
NOTE
Even in louver lock mode, the louver temporarily moves
in the following cases:
• When the air conditioner stops
• When heating starts
• When defrosting
• When the thermostat is off.
◆ Releasing the louver lock
Set "0000" in Step 4 of "Setting the louver lock".
The
mark disappears.
* Steps 1 - 3 and 5, 6 of
"Setting the louver lock" also
SET DATA
apply to releasing the lock.
23-EN
◆ Adjusting the horizontal direction
1
Push and hold the
and "TEMP.
buttons for at least 4 seconds while running
is stopped.
blinks.
"01" appears in CODE No.
2
UNIT LOUVER
Push the
button (left side of the button)
to select a unit
The unit number changes each time the button is
pushed.
Unit No.
Unit No.
1-2
1-1
No display
Unit No.
1-4
The fan of the selected unit runs, and the louver
swings.
3
Push the "TEMP.
" buttons to
change the CODE No. to "45".
4
Push the "TIME
"buttons to select a
direction.
Direction SET
Direction setting
DATA
Smudging reduction position
"0000"
(reduces ceiling smudging)
Cold draft preventive position
0000
"0002"
(Prevent cold draft)
[Factory default]
5
Push the
button to check the settings.
The indicator stops blinking and stays lit, and the
settings are confirmed.
6
Push
button to finish the setting.
* If the cold draft position is selected, the ceiling
smudging reduction effect will be reduced.
 4-way Cassette type
"
▼ When cooling
Point the louver horizontally.
▼ When heating
Unit No.
Point the louver downward.
1-3
• The louver automatically closes when the unit stops
running.
• In the pre-heating mode, the louver points upward.
The swing indication appears on the remote control
even in pre-heating mode, however the actual swing
starts only after pre-heating is complete.
▼ 2-way and 3-way air discharge
The air discharge can be changed to the 2-way or 3-
way type to suit the room shape and style.
For details, contact the dealer where you purchased
the air conditioner.
 Ceiling type
Vertical adjustment
▼ When cooling
Point the louver horizontally to send cool air across the
entire room.
– 12 –
▼ When heating
Point the louver downward to send heated air to the
floor.
• The louver automatically points upward when the
unit stops running.
• In pre-heating mode, the louver points upward.
The swing indication appears on the remote control
even in pre-heating mode, however the actual swing
starts only after pre-heating is complete.
Horizontal adjustment
When adjusting the louver direction horizontally, point
the vertical grille inside the horizontal louver in the
preferred direction.
◆ Unit select
• When two or more indoor units are controlled with
one remote control, the louver direction can be set
for each indoor unit by selecting them individually.
• To set the louver direction individually, push the
UNIT LOUVER
button (left side of the button) to display an
indoor unit number in the control group. Then set the
louver direction of the displayed indoor unit.
• When no indoor unit number appears, all indoor units
in the control group can be controlled
simultaneously.
• Each time the
UNIT LOUVER
(left side of the button) is
pushed, the indication changes as follows:
No
Unit No.
Unit No.
display
1-1
1-2
Unit No.
Unit No.
1-4
1-3
EN
24-EN

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mcy-map0487hs-ulMcy-map0607hs-ul

Table des Matières