Toshiba Carrier MCY-MAP0367HS-UL Manuel Du Propriétaire page 12

Masquer les pouces Voir aussi pour MCY-MAP0367HS-UL:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3
Push the
SWING/FIX
button to confirm the
direction of the selected louver.
Each time the button is pushed, the indication
changes as follows:
(1)
(2)
(3)
(4)
(7)
(6)
(5)
* When cooling or drying, (4) and (5) do not
appear.
◆ Setting the swing pattern
1
SWING/FIX
Push and hold the
FIX for at least 4
seconds while the operation is stopped.
blinks.
2
Push the
UNIT LOUVER
button (left side of the button)
to select a unit.
The unit number changes each time the button is
pushed.
Unit No.
Unit No.
Unit No.
1-1
1-2
1-3
No
Unit No.
display
1-4
The selected unit's fan runs, and the louver
swings.
3
Push the
buttons to select a swing
type.
Swing code
Swing code
Movement pattern
Standard swing
0001
(factory default)
0002
Dual swing
0003
Cyclic swing
REQUIREMENT
Do not set "0000".
(The louver may be damaged.)
21-EN
4
Push the
button.
5
Push the
button to finish the setting.
▼ Standard swing
All four louvers swing simultaneously at the same
angle.
Swing
▼ Dual swing (Recommended for heating)
• Adjoining louvers alternately point horizontally and
downward to heat the room evenly.
• Air blown downward reaches the floor, and air blown
horizontally is spread to circulate heat.
Horizontal
Horizontal
Downward
Downward
Horizontal
Horizontal
Downward
Downward
– 11 –
▼ Cyclic swing (Recommended for cooling)
All four louvers swing at different times like waves.
(2)
(3)
(1)
(4)
(2)
(4)
(1)
(3)
(1)
(2)
(4)
(3)
(2)
(1)
(3)
(4)
◆ Setting the louver lock
1
UNIT LOUVER
button (right side of
Push and hold the
the button) for at least 4 seconds while
running is stopped.
blinks.
• When no unit number appears, all units are
selected.
2
Push the
UNIT LOUVER
button (left side of the button)
to select a unit.
The unit number changes each time the button is
pushed.
Unit No.
Unit No.
Unit No.
1-1
1-2
Unit No.
1-4
The selected unit's fan runs, and the louver
swings.
3
Push the "TEMP.
display the number of the louver to fix its
direction.
The selected louver swings.
4
Push the
buttons to select the
direction of the louver you do not want to
swing.
(1)
(2)
0001
0002
(4)
(5)
0004
0005
* If (4) or (5) is selected, condensation may occur
during cooling.
Electrical control box
03
Refrigerant
pipe
04
Drain pipe
01
5
Push the
button to confirm the setting.
When the setting is confirmed, the
up.
(To set the louver lock of another unit, repeat steps
2-5. To set another louver lock of the same unit,
repeat steps 3-5.)
1-3
" buttons to
(3)
0003
02
mark lights
22-EN

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mcy-map0487hs-ulMcy-map0607hs-ul

Table des Matières