Ibiza sound DJ21USB-BT Manuel D'utilisation page 3

your amplifier.
3. The MIC L (15) and MIC R (16) input accepts a 1/4" connector.
4. On the rear panel are two stereo PHONO/LINE (17) & (18) inputs and 1 stereo LINE (19) input. The
PHONO/LINE (4) enables you to set the (17) input to phono or Line. The PHONO/LINE (6) enables you to
set the (18) input to phono or Line. The USB/LINE (8) enables you to set the input to USB or Line (19).
Headphones can be plugged into the rear panel mounted HEADPHONE (14) jack.
Operation
1. POWER ON: Once you have made all the equipment connections to your mixer, press the POWER (12).
The power will turn on and the POWER LED (22) will glow RED.
2. CHANNEL 1: SWITCH (4) allows you to select the PHONO 1/LINE 1 (17) jack to input phono or line level.
The CHANNEL SLIDE (5) controls the input level of this channel.
3. CHANNEL 2: SWITCH (6) allows you to select the PHONO 2/LINE 2 (18) jack to input phono or line level.
The CHANNEL SLIDE (7) controls the input level of this channel.
4. CHANNEL 3: SWITCH (8) allows you to select the USB OR LINE 2 (19) jack to input mp3 or line level. The
CHANNEL SLIDE (9) controls the input level of this channel.
5. CROSSFADER: The CROSSFADER (10) allows you to the Mixing CH1/CH2 source into another.
6. TALKOVER (3): The purpose of the talkover section is to allow the program playing to be muted so that
the mic can be heard above the music. When you press the SWITCH, the talkover will be on and the
volume of all sources except the Mic inputs are lowered by 12 dB. The Micro (2) allows you to control the
level of MIC1/MIC2.
7. Connect your headphones to the headphones socket and select the desired channel (channel 1-3 or MIC)
for monitoring with the Cue switch(1). With this knob PHONE(11), you can adjust the headphones
volume
8. DISPLAY: The DISPLAY (13) indicates either the MASTER output left and right levels.
9. The USB (23) jack can connect to USB stick that contains exclusively MP3 files.
10. |<< (24) : Use this button to re-start the track or to select the previous track.
11. Play/Pause (25): Each time you press this button, the operation changes from play to pause or from pause
to play.
12. >>| (26): Use this button to select the next track.
13. VOL-(27): Use this button to control level down of the MP3 player.
14. VOL+ (28): Use this button to control level UP op the MP3 player.
15. EQ (29): Allow you to select the effect.
16. LED DISPLAY (30): Display to MP3's information.
17.
BLUETOOTH LED (31): It displays the Bluetooth operating status. When you turn on the power, the
Bluetooth LED is flashing slowly which means that it is ready to connect to a Bluetooth device. If no
connection is found after 1 minute, le LED goes out and enters into standby mode. If the Bluetooth
connection is made with a player, the light flashes slowly, about 2-3 seconds flicker once. At this point you
can use the Bluetooth player playing music can hear the music of the corresponding channel.
BLUETOOTH PAIRING PROCEDURE
1. Set the selector switch of channel 1 to BT (center position). Set your Bluetooth device (e.g. mobile phone) to
Bluetooth connection mode. Switch the mixer on. The BLUETOOTH LED will flash slowly. Select
"BLUETOOTH" among the found devices on your mobile phone. You can now play music via CHANNEL1 of the
mixer.
©Copyright LOTRONIC 2013 DJ21USB-BT 3