Velleman CCTVPROM11 Guide D'installation Rapide page 6

rea ar panel
VID DEO IN 4 video
MO ONITOR connec
AU UDIO IN 1 audio
AU UDIO OUT 1 audio
LA N port Connec
VG GA connec
EX XTERNAL I/O use a 9
19 V DC Power
6. . Hardwa are setup
In stalling the e Hard Disk
•
Obtain a su uitable HDD
be formatte ed.
•
Make sure e to unplug t
to avoid ele ectrostatic di
•
Unscrew th e 6 screws (
•
Lift the cov er (back firs
•
Screw the m mounting bra
Note: the e PCB must b
•
Connect the e SATA data
•
Screw the H HDD on the
•
Close the co over (front f
A A
power supply
Co onnecting a a video mon
•
Obtain a su uitable monit
Note: when n both a CRT
force the output
Co onnecting th he power s
•
Plug the DC C output con
W WARNING: only use the
•
Plug the inc cluded powe
not switch the DVR on
Co onnecting a a camera
•
Connect the e video outp
Note: video o system is d
befo re the DVR
Co onnecting a audio
•
The DVR su upports one
DVR. Conne ector type is
•
There is als so an audio o
desired. Co nnector type
Co onnecting L Local Area N
V. 03 - 17/01/20 012
CC
o input chan nnels to conn
ct a CRT mo nitor to this
o input chan nnel to conne
o output to c connect to a
ct the DVR t to a local net
ctor for video o monitor
9 pin DSUB c connector to
supply input t.
p
k Drive (HD DD)
(not included d), type SAT
the device fr om the main
ischarge.
(1 on either side and 4 o
st).
ackets on th he HDD (scre
be facing up wards when
cable and p power supply
bottom of th he DVR hous
first) and sec cure it with t
B
data bus (SA d ATA)
nitor
tor (not incl. ) and conne ect it to the B
T and VGA m monitor are c
to the CRT m monitor port
supply
nector of th e power ada
e included a daptor.
r cable into the adaptor
yet.
put of the ca mera to eith her video inp
detected aut tomatically;
is powered-o on.
audio input . Connect th
s RCA.
output conne ector. Conne
e is RCA.
Network (L AN)
CTVPROM 11
nect 4 extern nal video sou
output
ect an extern nal audio so
n audio dev ice, e.g. a sp
twork by plu ugging a netw
o connect ex xternal signa
TA (Serial Ad dvanced Tec
ns before se rvicing and d
on the back) that hold th
ews included d).
mounting t he HDD into o the DVR.
y to the HDD D.
sing PCB faci ing upwards
the 6 screws s.
BNC or VGA
connected, p press and ho old the
t.
aptor into the e 19VDC pow
input conne ector and plu
put at the ba
therefore it is important
e audio outp put of an aud
ect an audio device e.g.
6
urces.
urce e.g. fro om a camera a with audio.
peaker (mon no).
work cable i nto this port
ls e.g. alarm m, sensor, ...
hnology Atta achment). T
do not touc h any electr
he cover in p place.
using the in ncluded scre
*HDD n not included
video outpu ut on the bac ck of the DVR
but tton during s
wer input at the back of f the DVR.
ug the other end into the
ck of the DV VR. Connecto
t that the ca ameras are p power-suppli
dio source to o the audio i
a speaker to o this conne
.
t.
.
he HDD mus st
onic circuitry y
ws.
R.
start-up to
e mains. Do
or type is BN NC.
ied
input of the
ctor when
n nv
©Velleman