Oregon 510A Manuel D'utilisation page 4

! CAUTION - SETTING UP THE GRINDER
The grinder must only be used in a place that is protected from dust and
dampness, that is well-lighted, out of the reach of children, and away from
gasses or other inflammable or explosive liquids.
The grinder must be situated near a normal electrical outlet equipped with
earth (grounded).**Avoid using dangerous extension cables.
**GROUNDING INSTRUCTIONS.
A. In the event of malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet
installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. The conductor with insulation having an outer surface that is green
with or without yellow stripes is the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions
are not completely understood, or if in doubt as to whether the tool is properly
grounded.
Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole
receptacles that accept the tool's plug. Repair or replace damaged or worn cord
immediately.
B. Grounded, cord-connected tools intended for use on a supply circuit having a
nominal rating less than 150V~. This tool is intended for use on circuit that has an
outlet that looks like the one illustrated in sketch A in figure. The tools has a grounding
plug that looks like the plug illustrated in sketch A in figure. A temporary adapter,
which looks like the adapter illustrated in sketches B and C, may be used to connect
this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly grounded
outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and
the like, extending from the adapter must be connected to a permanent ground such
as a properly grounded outlet box.
Grounding methods
GROUNDING PIN
ADAPTER
GROUNDING MEANS
2. GENERAL INFORMATION
The manufacturer is not liable for damages in the following cases:
- failed observance of the instructions given herein;
- use of the machine other than that described in the "INTENDED USE" section;
- failed use in compliance with current standards on Health & Safety at the
workplace;
- Incorrect installation;
- lack of scheduled maintenance;
- modifications or jobs that are not authorized by the manufacturer;
- use of non-original or inadequate spare parts;
- repairs that are not carried out by a specialist.
3. WARRANTY
The warranty validity is that acknowledged in the country of sale. Claims
under warranty will only be accepted if they are backed-up by the copy of the
purchase document (bill or receipt).
The guarantee becomes void if:
a) the machine has been tampered with;
b) the machine has not been used according to this manual;
c) non-original parts, machines or grinding wheels have been fitted on the grinder or
other parts that are not authorized by the manufacturer;
d) the machine has been powered at a voltage or frequency different from that written
in the rating nameplate.
4. USING AND kEEPING UP THE OWNER'S MANUAL
The characteristics and the information given in this manual are merely indicative.
The manufacturer reserves the right to add any modifications to the grinder
considered necessary at any time.
It is forbidden to reproduce any part of this document without authorization on behalf
of the manufacturer.
The owner's manual is integral part of the machine and must be kept in a safe place
so that it can be consulted whenever need be.
If you should loose your manual or it should deteriorate, you can request your dealer
or an authorized service centre for another copy.
The manual shall accompany the machine at all times, especially if it is sold on at
a later date.
2 2
P00801078_R00_510A_U&M_OR_120V.indd 2
EN
METAL SCREW
COVER OF
GROUNDING
OUTLET BOX
5. DEFINITIONS
Skilled technician: a person who is generally employed by the service centre and who
is trained to carry out extraordinary maintenance jobs and repairs on the machine.
6. SYMBOLS
This symbol points out the possibility of serious personal injuries if the
provisions and instructions are not complied with.
This symbol points out that the user must wear protection goggles when
he uses the machine.
This symbol points out that the user must wear protective gloves when
he uses the machine.
This symbol points out the correct running direction of the machine
(grinding wheel).
7. TECHNICAL DATA
Model
Voltage
Rated power
Grinding wheel dimensions
Maximum speed of grinding wheel
Acoustic pressure level
Level of vibrations on operating handle
Types of chains that can be
sharpened
Weight (complete machine)
8. PART DESCRIPTION (FIG.1)
1 Base unit
2 Arm-motor unit
3 Vise assembly
4 Chain blocking handle
5 Vise adjustment knob
6 Chain jaws
7 Chain blocking unit adjustment knob
8 Chain blocking unit adjustment knob
9 Chain blocking unit
10 Arm blocking handle
9. SAFETY DEVICES
The grinder is equipped with the safety devices illustrated hereafter:
- Shield guards: they protect the operator from parts of the grinding wheel that may
come away during the sharpening process.
These guards must always be fitted in place when the machine is in use.
Always make sure the guards are efficient and fitted properly. Operator safety could
be compromised if the guards are damaged and/or cracked.
- Switch: the machine features a safety switch with release coil. In the case of a
sudden power failure, the switch trips automatically and disconnects the machine
from the mains. The machine will not start even if the power supply is suddenly
restored. You need to reset the switch to start the machine again.
10. INTENDED USE
This machine is an electrical grinder for chains used in chain saws.
- Use the machine exclusively for the types of chains stated in the technical data chart.
- Do not use the machine to cut or grind anything other than the chains envisaged.
- Secure the machine firmly to the bench or wall.
- The machine must not be used in corrosive or explosive environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following improper or incorrect use of
the machine.
11. UNPACkING
The grinder is supplied already partially assembled.
12. STANDARD SUPPLY (FIG.2)
1 - Base unit
2 - Arm-motor unit
3 - Owner's manual
4 - Test card
5 - Shield guard
Grinding wheel Ø 5 3/4"x1/8"x7/8"
6 -
(145x3.2x22.2 mm)
Grinding wheel Ø 5 3/4"x3/16"x7/8"
7 -
(145x4.7x22.2 mm)
Grinding wheel Ø 5 3/4"x1/4"x7/8"
8 -
(145x6x22.2 mm)
9 - Extra shield guard
10 -Guard securing screw M5x12
510A
120V~ 60Hz
300W
Outside Ø : 5 3/4" (145 mm)
Inside Ø: 7/8" (22,2 mm)
Thickness: 1/8" (3.2mm)
3/16" (4.7mm)
1/4" (6.0 mm)
-1
3400 min
77 dB(A)
2
< 2,5 m/s
1/4" - .325" - 3/8" - .404"
13.25 pounds (6 kg)
11 Arm operating handle
12 Shield guard
13 Arbor shield
14 Grinding wheel
15 Sharpening depth adjustment knob
18 Main ON/OFF switch
19 Electrical power cable
20 Rating nameplate
21 Chain centring adjustment screw
11 - Washers for screws M5
12 - Arm securing screw M10x40
13 - Washer for screw M10
14 - Arm blocking handle
15 - Arm securing nut M10
16 - Operating handle
17 - Operating handle securing screw M6x25
18 - Operating handle securing nut M6
19 - Sharpening template
20 - Dressing brick
21 - 4 mm Allen wrench
22 - 5 mm Allen wrench
28/11/2008 9.47.31