Elica EMD530S3 Guide D'utilisation, D'entretien Et D'installation page 7

2. To wire through top:
Mark a line distance "A" from the left of the centerline on the
underside of the cabinet. Mark the point on this line that is
19⁄16" (4 cm) from back wall. Drill a 11/4" (3.2 cm) diameter hole
through the cabinet at this point.
A
A. 12" (30.5 cm) for 30" (76.2 cm) models
121/4" (31.1 cm) for 36" (91.4 cm) models
3. To wire through wall:
Mark a line distance "A" from the left of the centerline on the
underside of the cabinet. Mark a point on this line that is 1"
(2.54 cm) from back wall. Drill a 11/4" (3.2 cm) diameter hole
through the cabinet at this point.
A. 12" (30.5 cm) for 30" (76.2 cm) models
121/4" (31.1 cm) for 36" (91.4 cm) models
STYLE 1 - CUT OPENINGS FOR 3¼" X 10" (8.3 CM X 25.4 CM)
RECTANGULAR VENT SYSTEM
Wall venting
To make a 4" x 10½" (10.2 cm x 26.7 cm) rectangle in the wall:
1 Draw one line 2 ⁄ " (7.0 cm) and a second line 6
3
4
cm) below the underside of the cabinet. Extend these lines
through the centerline on the back wall.
2 Draw lines 51/4" (13.3 cm) to the right and left of the
centerline on the wall. Make sure these lines intersect with
the lines you drew in Step 1.
3 With the lines you drew as a guide, use a saber or keyhole
saw to cut a rectangular opening in the wall for the vent.
Cabinet
front
2 ⁄ " (7.0 cm)
3
4
6 ⁄ " (17.1 cm)
3
4
5
(13.3 cm)
19⁄ 1 6" (4 cm) from
wall, not cabinet
frame
Centerline
1" (2.5 cm)
A
Centerline
⁄ " (17.1
3
4
Centerline
⁄ " 5 ⁄ "
1 1
4 4
(13.3 cm)
STYLE 2 - CUT OPENINGS FOR TOP VENT OUTLET
(FROM RECTANGULAR TO 6" (15.2 CM) ROUND VENT SYSTEM)
Roof venting
To make a 6 ⁄ " x 8½" (16.5 cm x 21.6 cm) rectangle in the
1
2
cabinet bottom:
1 Draw a line ½" (1.3 cm) from the back wall on the centerline
of the underside of the cabinet, and then draw another
line 6½" (16.5 cm) from the first line.
2 Draw lines 41/4" (10.8 cm) to the right and left of the centerline
on the underside of cabinet.
3 With the lines you drew as a guide, use a saber or keyhole
saw to cut a rectangular opening for the vent.
*From wall, not cabinet frame
To make a circular vent opening on the underside of the
cabinet top:
1 Draw a centerline on the underside of the top of cabinet.
2 Draw a line 3
⁄ " (9.7 cm) from the back wall on the underside
7
8
of the top of cabinet. Make sure the line intersects with the
line you drew in Step 1.
3 Where the two lines intersect, use a compass or a circle
template to draw a 61/4" (15.2 cm) circle.
4 With the circle you drew as a guide, use a saber or keyhole
saw to cut the circular vent opening.
Circular vent opening
*37/8"
(9.7 cm)
*From wall, not
cabinet frame
Install vent system
1 Install the vent through the vent opening in cabinet or
wall. Complete venting system according to the selected
venting method. See "Venting Requirements" section.
2 Use caulking to seal exterior wall or roof opening around
the cap.
6 ⁄ "
1
4
15.8 cm
Cabinet
cutouts
7