Baby Jogger CITY TOUR LUX Mode D'emploi page 12

FRAME
EN
1 Unpack the stroller frame from the
box and set the wheels aside. Unlock
the stroller by pulling the
Storage Lock Lever.
2 Lift the front stroller frame away from
the rear stroller frame.
3 Lift the upper frame up and away
from the lower frame.
4 Rotate the handlebar up. The stroller
will lock into place and you will hear a
click.
WARNING: Ensure that all the locking
devices are engaged before use.
WARNING: Moving parts when
folding and unfolding stroller can
cause injury. Children should stay
clear when folding and unfolding.
FRONT WHEEL
5 Installation
• Lay stroller on its back so the
handlebar is resting on the floor.
• Attach the front wheel by sliding
it into the front wheel mount until
it clicks. Gently pull on the front
wheel to make sure it is properly
attached.
6 Removal
• While pressing the front wheel
release button, gently slide the front
wheel out of the front wheel mount.
SWIVEL FEATURE
7 Push the swivel lock button up
to lock the front wheel to a fixed
position.
8 Press the swivel lock button down
to allow the front wheel assembly to
swivel.
WARNING: When loading and
unloading child, lock the front wheel
in a fixed position. Although the front
wheel of your stroller locks, it is not
intended for jogging or exercise
purposes.
REAR WHEELS
9 Installation
• Align the rear wheel axle with the
wheel mount on the stroller frame
and insert it into the wheel mount
until it locks into place. You will hear
a click.
• Gently pull on the rear wheel to
make sure it is properly attached.
10 Removal
• While pressing down on the wheel
release button, gently slide the rear
wheel out of the wheel mount.
BRAKE
11 To lock the brakes: Rotate the brake
lever down to engage the brakes.
12 To release the brakes: Push the brake
release button.
WARNING: Ensure that the brake
is properly engaged by moving
the stroller slightly back and forth.
Lock the brakes before loading and
unloading your child and whenever
the stroller is not moving.
ATTACHING THE CANOPY
13 Insert the ends of the canopy into
the seat frame.
14 Loop the small strap to the hook on
the sides of the seat.
15 From the back of the seat, zip the
canopy to the seat.
ATTACH SEAT
16 To attach the seat frame to the
stroller frame: Unfold the seat and
lower the seat onto the stroller frame
mounting brackets. You will hear a
click when it is securely attached.
• The seat may also be attached
rear-facing.
17 To remove the seat: Lift up on the
seat release levers.
CANOPY
18 Pull forward to open canopy, push
backwards to close canopy.
19 To use the canopy extension: Pull the
extension out from under the canopy,
push the extension under the main
canopy to hide.
20 When folding the double visor, make
sure to fold each section of the visor
one by one.
ADJUSTING SHOULDER STRAPS
21 From the back of the seat locate the
plastic square stopper. Turn stopper
and pass through the openings in the
seat back frame and seat fabric.
22 Reinsert stopper at seat opening
closest to child' s shoulders. Pass
back through seat fabric and the seat
back frame. Tug on strap to ensure
stopper is locked. Repeat on both
sides.
WARNING: Avoid serious injury from
falling or sliding out. Always properly
adjust and fasten safety harness.
23 Slide the harness pads up to access
plastic guide on strap.
24 Hold the plastic guide and pull strap
to tighten or loosen.
USING SAFETY HARNESS
25 Insert the waist strap buckle parts
into the shoulder strap buckle parts
on both sides.
26 Insert the connected shoulder and
waist strap buckle parts into the sides
of the crotch buckle.
12
EN EN