Symbols On The Tool; Initial Operation - Metabo T 24-230 MVT CED Mode D'emploi

en ENGLISH
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Prior to each use, check if there are parts missing,
worn, broken, torn or damaged. Do not use a
defective or incomplete guard.
Use only the supplied clamping devices.
Additional Warnings:
WARNING
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.

SYMBOLS ON THE TOOL:

...... Class II Construction
...... Spindle thread
V.......... volts
A.......... amperes
Hz........ hertz
~
.......... alternating current
n .......... rated speed
../min ... revolutions per minute
rpm ..... revolutions per minute
4. Overview
See pages 2 and 3.
1 Extractor connection piece
2 Thread for side handle (on both sides)
3 Clamping nut (cutting depth limitation)
4 Scale (depth of cut)
5 Allen screwdriver
6 Side handle (of the angle grinder) *
7 Push machine only in direction of arrow
8 Extraction guard
9 Arrow indicating direction of rotation (direction
of rotation of the diamond cutting disc)
10 Guide table
11 Spindle locking button (of the angle grinder) *
12 Main handle of the angle grinder *
13 Spindle (of the angle grinder) *
14 Support flange (of the angle grinder) *
15 Three spacer discs
16 Diamond cutting disc *
17 2-hole adjusting nut
18 two-hole spanner
19 Clamping ring
8
California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
20 Clamp screw
21 Button (to turn the main handle) *
22 Lock (to prevent the machine from being
switched on unintentionally, or for continuous
operation)*
23 Trigger (for switching on and off) *
* not in scope of delivery/ depends on equipment

5. Initial Operation

Prior to any conversion work: pull the mains
plug out of the socket. The machine must be
switched off and the spindle at a standstill.
Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Use only extension cables with a minimum cross-
2
section of 1.5 mm . Extension cables must
correspond to the power consumption of the
machine (cf Technical Specifications). If a cable
roller is used, always roll up the cable completely.
5.1 Attachguard at the angle grinder
Dismantle the extraction guard (8) and guide
table (10)
See page 2, fig. A.
1. Loosen clamping nut (3) and swivel extraction
guard (8) upwards.
2. The extraction guard (8) can be removed from
the guide table (10) in the shown position.
Attach the extraction guard (8) to the angle
grinder
See page 2, fig. B.
3. Loosen the clamping screw (20) until the
clamping ring (19) on the extraction guard
expands sufficiently.
4. Attach the angle grinder in the shown position to
the extraction guard (8).
5. Rotate angle grinder and fix at the desired angle,
see page 3, fig. E:
I) Pushing cut
II) Pulling cut
6. Firmly tighten the clamping screw (20)using the
supplied Allen screwdriver (5).
7. Make sure that the extraction guard is seated
securely - you should not be able to turn the
safety guard (8).
Assemble the extraction guard (8) and guide
table (10)
See page 2, fig. A.
8. Place the recess of the extraction guard (8) as
shown into the axle of the guide table (10).
9. Swivel the extraction guard (8) and the guide
table (10) into each other, set the desired cutting
depth and connect to each other by tightening
the clamping nut (3).
10.Check for secure connection.