Installation Requirements; Tools And Parts; Location Requirements - Whirlpool 3XWTW5905SW0 Instructions Pour L'installation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Tools and Parts

Gather the required tools and parts before starting installation.
The parts supplied are in the washer basket.
Tools needed for connecting the drain hose and water
inlet hoses:
Pliers that open to
3.95 cm (1⁹⁄₁₆")
Parts supplied:
A
C
A. Water inlet hose (2)
B. Drain hose form
C. Large flat washer (4)
Tools needed for securing the drain hose and leveling
the washer:
Adjustable or open end
wrench 14 mm (⁹⁄₁₆")
Level
Parts supplied:
A
A. Beaded tie strap
B. Front leveling feet with nuts (2)
2

INSTALLATION REQUIREMENTS

Flashlight (optional)
B
E
D
D. Small flat washer (2)
E. Inlet hose adapter
Wood block
Ruler or measuring tape
B
Alternate Parts
Your installation may require additional parts. Forinformation on
ordering, please refer to the toll-free phone numbers on the front
page of the Washer User Instructions.
If You Have:
You Will Need to Buy:
Laundry tub or
Sump pump system (if not already
standpipe taller
available)
than 2.4 m (96")
2.5 cm (1")
3.2 cm (1¹⁄₄") diameter to 2.5 cm (1")
diameter
diameter standpipe adapter kit,
standpipe
Part Number 280130
Overhead sewer
Standard 76 L (20 gal.) 99 cm (39") tall
drain tub or utility sink, sump pump and
connectors (available from local
plumbing suppliers)
Floor drain
Siphon break kit, Part Number 280129;
additional drain hose,
Part Number 3357090
Water faucets
2 longer water fill hoses:
beyond reach of fill
1.8 m (6 ft) Part Number 76314,
hoses
3.0 m (10 ft) Part Number 350008
Drain hose too
Drain hose kit, Part Number 280131
short
Lint clogged drain
Drain protector, Part Number 367031

Location Requirements

Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed in a basement, laundry room, closet,
or recessed area. See "Drain System."
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
A water heater set to deliver 49°C (120°F) water to the washer.
An earthed electrical outlet located within 1.2 m (4 ft) of where
the power cord is attached to the back of the washer. See
"Electrical Requirements."
Hot and cold water faucets located within 90 cm (3 ft) of the
hot and cold water fill valves, and water pressure of 34.5-
690 kPa (5-100 psi). Washers with triple dispensers require
138-690 kPa (20-100 psi) for best performance.
A level floor with a maximum slope of 2.5 cm (1") under entire
washer. Installing the washer on carpeting is not
recommended. Ventilation openings in the base must not be
obstructed by carpet.
A sturdy floor to support the washer weight (washer, water
and load) of 143 kg (315 lbs).
Do not store or operate your washer in temperatures at or below
0°C (32°F). Some water can remain in the washer and can cause
damage in low temperatures. See "Washer Care" in the Washer
User Instructions for winterizing information.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

3xgsc9455jq63xlsq7533jq53xlbr5432jq5

Table des Matières