Publicité
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
•
Wear ear-muffs.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Risk of eye damage if suitable safety goggles
are not worn.
This equipment generates an electromagnetic
fi eld during operation. Under certain circumstan-
ces this fi eld may actively or passively impede
medical implants. To reduce the risk of serious
or fatal injuries, we recommend persons with
medical implants to consult their doctor and the
manufacturer of the medical implant prior to using
the equipment.
5. Before starting the equipment
Important!
The machine is supplied without batteries and
without a charger!
Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Fitting the blower tube (Fig. 3a/b)
Plug the blower tube onto the motor unit. The
groove (A) must be pushed into the guide (B)
when you do this. Turn the blower tube to the right
to secure it in its fi nal position on the motor unit.
Caution! The tube must be turned as far as it will
go to make sure it is fi rmly secured in position.
Anl_18VBL2_665_1_SPK7_PRINT.indb 122
Anl_18VBL2_665_1_SPK7_PRINT.indb 122
GB
5.2 Fitting the battery (Fig. 4)
Important! Before fi tting the battery you must
always set the On/Off slide switch to OFF (see
section 6.1).
Press the pushlock button of the battery pack as
shown in Fig. 4 and push the battery pack into the
mount provided. When the battery pack is posi-
tioned as in Fig. 4, make sure that the pushlock
button latches in place! To remove the battery
pack, proceed in reverse order.
5.3 Charging the battery (Fig. 5)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to blink.
3. Insert the battery pack into the charger.
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 122 -
12.07.2024 11:44:40
12.07.2024 11:44:40
Publicité
