Technical Data; Noise/Vibration Information; Starting Operation; Working Advice - Bosch EasyHeat 500 Notice Originale

OBJ_BUCH-3137-001.book Page 11 Tuesday, November 28, 2017 9:26 AM

Technical Data

Heat Gun
Article number
Rated power input
Air flow
Temperature at the nozzle outlet
Temperature measurement accuracy
Weight according to EPTA-Procedure 01:2014
Protection class
1) The amount of air increases when the temperature rises from 50 °C to 300 °C. The speed of the fan is identical at both power settings.
2) At an ambient temperature of approx. 20 °C.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Typically the A-weighted sound pressure level of the product
is lower than 70 dB(A).
Total vibration values a (triax vector sum) and uncertainty K:
h
2 2
a ≤2.5 m/s , K=1.5 m/s .
h
Operation

Starting Operation

 Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the machine.
Creation of smoke during initial use
A coating protects the metal surfaces from corrosion ex-
works. This protective layer evaporates during initial use.
Switching On
Slide the on/off switch 2 upwards.
To save energy, only switch the power tool on when using it.
Switching Off
Slide the on/off switch 2 downwards into the 0 position.
 UniversalHeat 600: After working at high tempera-
tures for a prolonged period, let the power tool cool
down by briefly running it at the 50 °C power setting
before switching it off.
Selecting a power setting
You can choose between different power settings using the
on/off switch 2:
Power setting EasyHeat 500
°C l/min
–
300 240
500 450
UniversalHeat 600:
 When changing from 50 °C to 300 °C, the speed and
therefore the operating sound of the gun do not change.
The 50 °C power setting is suitable for cooling down a heated
workpiece or for drying paint. It is also suitable for cooling
down the power tool before putting it down or changing the
attachment nozzles.
Bosch Power Tools
2)

Working Advice

 Before any work on the machine itself, pull the mains
Note: Do not apply the nozzle 3 too close to the workpiece be-
ing worked. The hot air build-up can lead to overheating of the
power tool.
Removing the Heat Protection (UniversalHeat 600)
The heat protection collar 4 can be removed when working at
particularly hard-to-reach locations.
 Be careful of the hot nozzle! Increased danger of burning
To remove or mount the heat protection collar 4, switch the
power tool off and allow it to cool down.
To speed up the cooling, the power tool can also be operated
for a short period with the lowest adjustable temperature.
Placing Down the Power Tool (see figures D and F)
To cool down the power tool or have both hands free, place it
down on the standing surface 1.
 Be especially careful when working with the placed
Work Examples (see figures A–F)
UniversalHeat 600
The figures of the application examples can be found on the
°C l/min
graphics pages.
50 200 The distance between the nozzle and the workpiece depends
–
on the material you are working on (metal, plastic, etc.) and
300 350
the intended working method.
600 500
The optimum temperature for each application can be deter-
mined by a practical test.
Always test the amount of air and temperature first. Start at a
greater distance and a lower power setting. Then adjust the
distance and power setting according to requirements.
If you are unsure what material you are working on or what
effect the hot air gun might have on it, first test the effect on a
concealed area.
EasyHeat 500
3 603 BA6 0..
W 1600
l/min 240/450
°C 300/500
±10 %
kg 0.47
/II
plug.
exists when working without the heat protection collar.
To remove the heat shield 4, turn it towards the open
lock.
To fit the heat shield 4, attach it and turn it towards the
closed lock.
down power tool! There is danger of burning oneself on
the hot nozzle or on the hot air jet.
1 609 92A 3U2 | (28.11.17)
English | 11
UniversalHeat 600
3 603 BA6 1..
1800
1) 1)
200 /350 /500
1) 1)
50 /300 /600
±10 %
0.53
/II